Counting matching models…
I wanted to display my iPod Classic 160GB and in Parallel have it on a Dock, so I created a small stand where you can put in the 30pin cable and charge it well. Printed with PLA and 5% infill (you could do more for stability)
Printer: Creality Ender 3 V2 NEO Filament: eSun PLA+ Orange Tailored for home and small office environments, this design incorporates additional options for mounting Mikrotik desktop devices on your network rack. If you have a design in…
As you all know, ipods are the slipperiest devices on planet earth, and i liked icomputer7's bumper case. Thin, unobtrusive, but the back of it was prone to breaking off because of a weak point in the walls where they connect to the base,…
With the new Guardians of the Galaxy movie out, I was inspired to make this case after seeing the one Star-Lord had for his Zune. Right now, Zunes are pricey and because of that, I would rather not lose/beat up the only one I have. So…
What? A Bike handlebar alignment tool that doesn't require hardware or tools or lasers - just hook it on the handlebars and go! The tool aligns on the handlebars and rests on the headtube. Slots in the gauge are sized for a variety of…
I didn't find a simple 100x100mm silica box, that i can print on my Voron 0.2, so i decided to do a quick simple one with heat set inserts an a screwed lid. The big box fits around 320g of Silica beads (See pictures). The small box fits…
My Wife wanted to buy those Donut weights from a content Creator, but they were out of Stock, so I made her even heavier ones. Also iterated on the design. If you use one of those fancy build plates with a pattern make sure to get a good…
The MR60FDA2 and MR60BHA2 Sensor leverage 60GHz mmWave technology and offer reliable human presence & fall detection, and human presence, breathing and heartbeat detection respectively. Featuring light level sensing, an RGB LED for…
Remix from the “Slim” model to fit the THICCer iPods with bigger HDDs.
DIRECT-DRIVE HOTEND SETUP Including The Sherpa Mini + Stock Hotend + Stock Levelprobe + ADXL345 I designed a new hotend mount for the Flsun QQ-S Pro, which provides the stock hotend setup in combination with sherpa mini extruder as…
Measuring spoon to get approx. 60g of sugar to feed my water kefir. Print upright with supports for the handle. Category: Kitchen & Dining
This is a remix of this fx-9750GII cover , chopped up and stretched out with some very hacky OpenSCAD to fit an fx-9860GII. As printed, the fit is a little tight. If you'd like to loosen it you can either increase the case_extra_width…
Desk stand for MikroTik RB260GS (Managed L2 Switch) This stand saves space and allows you to easily check the link LEDs. *I recommend printing with PETG-HF or PLA Basic. Tested on the following models: RB260GS (CSS106-5G-1S) RB260GSP…
Mikrotik Routerboard 260GSX wallmount This is based on tedder's Mikrotik RouterBoard Wall Mount for RB260GSP from Thingiverse Thicker base
I have tested it and works well with the default dimensions with the file I printed mine in ASA with a Sovol SV06 plus
Print in PETG - no supports
A 10-inch rack mountable case replacement to combine a mikrotik Hex S 2025 and RB260GSP into a 1U router/switch combination. The case is made of two parts which click together. To mount the devices M3 heated insets are used.
Full 1U rack mount for Mikrotik RB260GS, RB260GSP, HEX POE. Fits 3 devices. Use M3 Screws to connect the 3 segements
IO-Shield for MB MSI 760GM-P23 (FX)
Салазки для Mikrotik RB260GS в 10ти дюймовую стойку. Слева вырез для провода питания, справа логотип.
This is my take on a blades bin for Gridfinity. It's 2 x 1 x 10 “u”. It's 60g filament, but produces a nice solid print which doesn't give you any concerns that it might break at some point. It's intended to be disposable, ie no removable…
This little box is used to regenerate the 8gr boveda bags. Just put the distilled water in the container together with the bags, close the cap and wait a few weeks.
60g High-Airflow Silica Gel Container for Filament Spools Keep your filament dry while it is stored. I designed this reusable desiccant container to fit inside the center of a filament spool and provide as much airflow around the silica…
I really liked the original ESRack system design created by @EvilProphet . I created a module for MikroTik RB260GS from the ESRack Customizable Device Mount by @DavidKahler_64887 The ESRack system includes the following components:…
How many times you lost the plate of the motherboards? This is the one for Asrock 960GM. Print Settings Printer Brand: Prusa Printer: Prusa Clone **Rafts:** No Supports: No **Resolution:** 0.2mm Infill: 20% Category: Computer
I got the new insta360go v2 as a present paired with the lens guard ( https://store.insta360.com/product/go_2_lens_guard ) and I had no idea where to put them since they come without any sort of pouch or case, I then ordered some other…
These are remixes of the goober canopy mount for the Insta360go2. I worked with CiottiFPV to create multiple offsets for his "TinyLifter" concept. Category: 3D Printing
The PS3 60gb! It took me a while to get to this classic, so here it is (you can finally build a full family of playstations, from original to 4!)
Wall Mount for a Mono Price Blackbird Pro WiHD 60GHz HDMI Extender. For use with -→ https://www.monoprice.com/product?p_id=16049
0.8 MOD gear 65T (for the focuser wheel of the Nakoh 60GT telescope) , which can be applied for focus automation.
Ein Headset Halter der sich komplett ohne Anschlag um seine eigene Achse gedreht werden kann.
What? A Bike handlebar alignment tool that doesn't require hardware or tools or lasers - just hook it on the handlebars and go! The tool aligns on the handlebars and rests on the headtube. Slots in the gauge are sized for a variety of…
Салазки для Mikrotik RB260GS в 10ти дюймовую стойку. Слева вырез для провода питания, справа логотип.
This is my take on a blades bin for Gridfinity. It's 2 x 1 x 10 “u”. It's 60g filament, but produces a nice solid print which doesn't give you any concerns that it might break at some point. It's intended to be disposable, ie no removable…
Holder for MP4 player Lenco Xemio-860GN to be screwed with two screws. Be careful when cutting off the support..
The HH-60G Pave Hawk is a derivative of the UH-60 Black Hawk used by the USAF for search and rescue, MEDEVAC, and disaster relief. Sikorsky produces the Pave Hawk, which was first introduced in 1982. If you want to purchase this model…
