Counting matching models…
UPDATE 09/2024 Add new version V8 for G93SC and G93SD with monitor clip. You can clip this version to your monitor without additional tape. Would be nice to get feedback for G95SC. Add new version V5 to fit G95SC. Description This is my…
Print approx. €2.07–€2.53 excl. taxPreliminary estimate for PETGSource material: PET
Edit 01/2020 : Added a different version designed to be protected by epoxy resin. See the make for a preview. This is a round badge for replace the one one the side body of a BMW F800R 2010. This represent the coat of arms of germany.…
This mount allows a variety of ways to connect your tobii5 eye tracker to your curved monitor. Mine is an Alienware AW2334DWF which is a 1800R (radius in mm) Ultrawide. The aim was to have a removable tobii that was forward of the screen…
Awesomatix body Stopper. Made for A800R but fits also MMX and others. Distance between holes is 28mm
Clips onto the monitor. Made specifically for the G95SC.
This is a model to mount the 1UP fan on Awesomatix A800Rs. The local hobby shop was out of other fans when I built mine up and the 1UP fan seemed like a nice clean and tidy fan, not to mention they seem to make an extensive selection of…
This is a monitor shelf to hold my DSLR camera. It is designed around the Dell S3422DWG 34" Curved Gaming Monitor. That monitor has an 1800r curvature so it ***should*** work with others with the same curve. Hardware: 1 X screwdriver 2x…
The heat produced by the monitor makes the Tobii mounting solution fall off the monitor. This mount clips on the bottom of the monitor and the tobii mount attaches to it instead of on the monitor directly. 4 M4 screws needed to clamp down…
made to keep oiler lines from backing off the barb fitting
2023 Yamaha GP1800R Stock Grate Pump Plugs These plugs may fit other years of the GP1800R. Not all parts will need to be printed. It will depend on how you are planning on sealing the pump. For example, if you plan on using flex seal for…
The model allow mounting a lightbar or a webcam on OLED monitors with 5 mm thick screens, with a curvature of 1800R. Printed in PLA, no special features needed.
THIS IS UNTESTED I tried to mimic the oem BMW GPS mount in dimensions. The only difference is that you can't remove it as fast / steal it from the bike once fitted. It's usefull for a GPS, or a phone mount and this use the AMPS holes…
A modern motorcycle ABS works by comparing mainly 2 sensors : Front and Rear wheel speed (called ABS sensors, but used for ABS, speedometer and providing speed to the ECU for others uses). Add this to the front and the front sensor will…
With clip ons on a f800r 1st gen, you can expect blocking your thumb while turning. This model is here to decrease the turning radius by blocking the fork so you can't turn at the maximum. I suggest TPU or Flexfill 92. You will nead to…
turn signal housing (flexible part) for Honda VTX1800 I recommend using TPU. I used a 3-wall D60 TPU with 10-15% hydroid infill. I use square nuts m6 with dimensions 10*10*3.2 (or 3). The nuts are inserted during printing by pausing the…
Clips onto the monitor. Made specifically for the G95SC.
The model allow mounting a lightbar or a webcam on OLED monitors with 5 mm thick screens, with a curvature of 1800R. Printed in PLA, no special features needed.
UPDATE 09/2024 Add new version V8 for G93SC and G93SD with monitor clip. You can clip this version to your monitor without additional tape. Would be nice to get feedback for G95SC. Add new version V5 to fit G95SC. Description This is my…
Print approx. €2.07–€2.53 excl. taxPreliminary estimate for PETGSource material: PET
