Counting matching models…
Fan shroud to mount an Noctua NF-A4x10 to an LSI 9300-8i HBA. Design idea copied from @BlackHornet_355398 's fan shroud here: https://www.printables.com/model/377809-lsi-9300-16i-noctua-nf-a9x14-fan-shroud I have a LSI 9300-8i, but this…
Fan shroud to mount an Noctua NF-A4x10 to an LSI 9400-16i HBA. Design idea copied from @BlackHornet_355398 's fan shroud here: https://www.printables.com/model/377809-lsi-9300-16i-noctua-nf-a9x14-fan-shroud I have a LSI 9400-16i, but this…
Initially indended to print as a keychain but can also be used as a place holder for a 40mm fan in cad proojects.
I upgraded the fans on my Monoprice select mini from the cheap 30mm units to 40mm Noctua. I found a particularly nice design for a velocity stack for 40mm fans that I was going to print out, but discovered that it had a larger center hub…
Mounting kits for mounting 3 Noctua NF-A4x20/A4x10 fans above and 3 fans below the CPU cooler in Fractal Design Terra case. Can be used only in position number 1 of Terra's inner bracket. The top bracket connects to PCI-E riser included…
Additional parts needed: Rasberry Pi 4b 40 mm PWM 4V Fan (such as Noctua NF-A4x10 5V PWM) 4x M4 countersunk screw (Normally supplied with the fan) Optional: 4x M3 nut and 4x M3x6 screw (To screw Raspberry pi securely into the case) Print…
Fan cover A4x10 / A4x20 (Noctua) Cover for A4x10 and A4x20 fans. Just put it over and screw it with the fan. With and without cable routing available. The width has a little bit play, the height is adjusted to my printer, if needed…
LSI 9300-8i Fujitsu model remix of original. Below is link for onshape if you need to make more edits. Need supports as per the original.…
All Raspberry cases I have found were small, fancy, without possibility to mount a fan. So I have made one. It is not the smallest one or the fanciest case, but it is easy to print and there is possible to mount 40x10 fan (I am using…
Simple fan mount for Raspberry Pi Compute Module 4 (CM4). Fan is a noctua NF-A4x10 40mmx10mm. Requires no additional hardware, just snaps in. Has clearance for a low profile heatsink.
With a Noctua 40mm fan in hand, I decided to play around with air flow. This design pumps air from the back in the case past all the major components on the board. A little bit is diverted past the bottom to cool the M.2 slot. I set the…
Fan shroud for the Big Einsy case that hides the brown Noctua a4x10 fan and matches the case aesthetic. It also helps to protect the fan from debris that can cause damage. The fan should install into the shroud with a light press fit, i…
Print in PET-G. Holes are supposed to be tight with the standoffs. I can upload a looser one upon request. UPDATE 01/02/2025: Added STEP and Solidworks Maker (2025) files.
Noctua NF-A4x10 adapter for RaspberryPi 4B What is it? It fits Raspberry Pi4b dual fan aluminium radiator/fan case. Why? Bearing seized in one of original fans and I wanted to upgrade it with spare Noctua NF-A4x10 5v fan to make it quiter…
This case for RADXA Rock 3A needs 4x M3x20x6mm standoffs and is made for M3x5mm melt-in thread inserts. Mount the SBC on the case-base with the four M3 standoffs with M3 threads. To fix the top-case use 4x M3x6 or M3x8mm countersunk…
Fan shroud for the 40mm Noctua NF-A4x10 to cover it up and make it look better. Intended as friction mount - just put it on the fan and it should hold on there firmly. Arachne wall generation and smaller nozzle recommended.
My stock blower was dying and I was getting a lot of stringing, so I put these noctuas. This is specific for the Ender 3 Petsfang Bullseye Duct 9.27, which was made for the stock Ender 3 blower. Uses the screws that came with the Noctua…
This hotend fan mount fits a Noctua A4 fan or any other fan that's mounting hole distance is 32mm. Ruthex M3 heat insert are needed. Holes for these are 4mm in diameter and ~5.7mm deep. This is but a rough draft btw. So please bear in…
Cool drivers is necessary. My cnc 3018 from Banggood is overheating (drivers) so I want to cool it. I model this model in Fusion 360 for Dingqi Electronics cnc board. The board have 92mm wide and 72mm high. You just need to print, unscrew…
Big Einsy Cove Noctua NF-A4x10 5V. Noctua NF-A4x10 5V: https://www.amazon.de/dp/B00NEMGCIA Fan can be directly mounted to the Einsy Board 5V on the top right. You have to use the 2pin Adapter from the from the included accessories and…
I made this adapter for an aluminum cooling case for Raspberry Pi 4 that I ordered from AliExpress. The original case uses two small 25 mm fans, but I found them too loud for everyday use. To make the setup quieter, I designed this…
The model is not 100% finished: The corner rails of the lid don't fit the case at the moment, but you can easily clip them off and then the case works fine. It fit well enough for my usecase so I didn't go back to touch it up. If you want…
Noctua NF-A4x10 extension for E3D V6 mount for Ender 3 w/ BL Touch You need a Noctua NF-A4x10 and 2 m3 inserts.
Remixed fan cover for Noctua A4x10 Fan on a RaspberryPi with an Aluminum Armor/Heatsink Case as I needed something to keep the fan in place and to protect the fan blades/fingers. * This was printed in Bambu Labs Translucent PETG * Printed…
This simple little bracket dropped the temperatures of my LSI 9207-8i HBA card from almost 100C down to 39C (as measured by my temp guns). This can only help extend the life of the card. I remixed the original design to accomplish three…
Fan shroud for the 40mm Noctua NF-A4x10 to cover it up and make it look better. Intended as friction mount - just put it on the fan and it should hold on there firmly. Arachne wall generation and smaller nozzle recommended.
I made this adapter for an aluminum cooling case for Raspberry Pi 4 that I ordered from AliExpress. The original case uses two small 25 mm fans, but I found them too loud for everyday use. To make the setup quieter, I designed this…
