Counting matching models…
To replace a broken washer fluid reservoir cap for a OPEL Astra J OPC and some other OPEL models ;-) Original Part No. 13227300 Just printed in PETG orange / black. To hold the cap down i insert two magnets (4,5mm x 1,5mm x 9,5mm). MMU…
The MZ4250 Astral Exploration Ship is unofficial Fan Content permitted under the Fan Content Policy . Not approved/endorsed by Wizards. Portions of the materials used are property of Wizards of the Coast. ©Wizards of the Coast LLC. Want…
Remix with "Opel Emblem" "Astra K Innovation" lettering and suitable for my REDMI NOTE 10 PRO including rubber case. Also add a file WITHOUT the "Astra K Innovation" lettering Print Settings: Supports: Yes Resolution: 0.2 - 0.3 Infill:…
I ran into some snow in winter and lost the right cover of my headlamp washer. There seem to be two versions of washer covers out there and when I ordered a replacement, I always got the wrong one. 3D printing to the rescue... It was…
Filament: color fabb PETG/ASA Infil: >50% Support: yes Resolution: 0.2
The diameter inside is 61mm. Printed using PLA and it holds up over time!
After some Years, my OPC Key Buttons went away. To save the Key, i've desigend a new Inlay. Printed in TPU - works greate ! No clue needed ! DualColor MMU printable Print instructions I've printed the part on the textured Prusa Sheet to…
How to diagnose a failed heater flap: There is no hot air blowing from the HVAC in the Astra, First checked the coolant in the engine, if there is none, you might have a bigger problem. Check if the the mix flap solenoid is working by…
This trestle system allows for inclines and elevated sections of Fastrack. I have designed sections in 5mm (0.2in) increments. Combining this with 10inch sections of Fastrack will result in a 2% grade. It recommended to place a trestle at…
It must be printed with ASA for proper UV and temperature resistance. Use supports on build plate only. At least 50% infill is required.
Window lifter button for Opel Astra H 2000-2006 Printed in pla it didn't last long, I had it printed in resin from a friend and it has been working for 2 years
Porta cellulare per auto. Design per Opel Astra J le due braccia laterali che tengono fermo il cellulare possono scorrere nel body per adattare la lunghezza del cellulare utilizzato.
Opel/Vauxhall Astra G Keychains. Hatchback,Cabrio,Van,Caravan(wagon) and Coupe design.
Update 03/09/2023: I have added a new version, v.16, which removes some of the additional tolerances I added to accommodate ASA warping, in order to reduce stress on the pins on the side of the model. This version is designed to be made…
Kindle Fire Tablet 10 Inch (kids), Headrest, Car, Vehicle Mount, Designed for Vauxall/Opel, Zafira B, Astra G It may fit other vehicles with similar spacing of headrest posts. Printed in ABS to allow for a little shrinkage. I wouldn't…
Deutsch: Ich habe das Model mit Fusion 360 gemacht. (Part 2 ist editierbar) Es wird zusätzlich eine Handyhalter für ein Kugelkopf benötigt. Kosten zwischen 2 - 8€ je nach Ausführung. Part 2 wird einfach in Part 1 Gesteckt, bei mir wurde…
make sure to play around with irnoning and nozzle sizes, i made some mistakes but they mede it look better
Vaccine Vial Holder for PfizerBioNTech vials based on model created by: Ales Padrta and Zapadoceska Univerzita for hospital in Rokycany (…
cupholder with storage
To replace a broken washer fluid reservoir cap for a OPEL Astra J OPC and some other OPEL models ;-) Original Part No. 13227300 Printed in PETG The frame STL is identical to the original, only the lid has modifications.
Intro: This part is for the older opel astra models and it's the holder of the sun visor. After a few years they tend to break. I replaced this part for a friend. I reduced only one detail, because it was not necessary and not easy to…
Hatch for ashtray/compartment behind gear shift for Opel Astra J, there is place for 2mm magnets to prevent opening
I created this hubcap for my Opel Astra Print instructions I used PETG material I used support material
This is a conversion for the HG M1 Astray into the space-based counterpart from Gundam seed MSV and Astray manga. The rifle does fit the normal hand, however, I have made my own with a wrist joint to help with holding. Category: Model…
original files from: https://www.thingiverse.com/thing:3114789/files I successfully split the original USB connection from the car to 2 USB sockets with these components →…
For V2 i deepened the holes for the lettering to make it easier to read. The tokens themselves are rather large, i recommend scaling them to 20-25mm. V3 has been updated to have more orders on a diagonal to be farther from the edge.
Designová náhrada originální krytky šroubu tlumiče pro Opel Astra H
This is a model for GM/Opel/Vauxhall flex organizer hook. Best printed from hard TPU. Or use PETG/ASA/ABS 25% infill should be enough
As in Summary. It’s silhouette pack of: Astra G hatchback 3 door Astra G hatchback 5 door Astra G sedan Astra G combi Astra G panel van in 2 “heights” (it‘s technically width). 1,2mm great for wall 15mm stands by itself routhly 15cm I’m…
this was created under Riot Games' "Legal Jibber Jabber" policy using assets owned by Riot Games. Riot Games does not endorse or sponsor this project. dm me for more models, happy printing
Front Door Speaker Adaptor Astra H GTC (165mm)
Ein Ersatzteil für den Gewindetrieb eines Spiegelstellmotor des Opel Astra H (Corsa D). Für den Druck sollte ein SLA Drucker verwendet werden. Da die einzelnen Segmente das Gewindetriebs im Überlastfall überspringen können müssen, wurde…
Ersatzhebel für Deckel der Mittelarmlehne eines Zafira B oder Astra H Material sollte PETG oder ABS verwendet weren PLA nur bedingt (funktioniert aber bei mir schon einige Zeit mit PLA) Support nicht notwendig (maximal unter dem…
It's a Opel/Vauxhall Astra G OPC Keychain from side view.
Water bottle cap for wipers OPEL ASTRA H Filament TPU Printing on prusa MK4 100 % infill
I removed the split compartment in the front and the hole for the USB cable. I have my wifi dongle for the Android car in the arm rest, hence my USB is used anyways and I don't need to feed the cable through and I have the option of…
A suction cup mount for the FasTrak Flex (2022). Easy access to adjust the number of riders. I recommend 3 walls at 20% infill. If you're in a hot area, I recommend PETG or don't leave it out in the sun. Worked perfectly with the 20mm…
"A corpse should be left well enough alone." Out of all the five bosses from the DLC, I think Lady Maria was the most challenging to sculpt. It's simply the level of detail in her clothing that did it. Unfortunately the last week for me…
Good replica of the opel's armrest clip
The original file "Opel Vauxhall Zafira B Astra H Armlehne / Armrest by jogiarea" looks 100% like my broken off original 2010 Zafira armrest clip. That is very impressive, as it is a quite 3-dimensional design! Unfortunately, when I…
I'd suggests using a thin piece of clear plastic for the glass instead of printing it. split in parts Category: Props
Change without unscrewing the antenna. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Filament: Plastika Trček TPU Category: 3D Printing
A MagSafe Dock for the new iPhone 12 devices designed for the Opel/Vauxhall Astra G. The dock replaces one of the vents in the center console (if flipped, you could probably also replace the vent left of the steering wheel). The MagSafe…
This custom-designed 3D printed floor mat clip is made specifically for Opel Astra J models. It fits perfectly into the original mounting point and securely holds the floor mat in place. 3D printed clip for Opel Astra J. Fits the original…
I've designed this holder to be more suited for a smartphone in a case (etui) which makes it quite thick. It is easy to place and remove. If you need to make this holder more suitable for your phone, you can simply scale it a little bit…
This is a railroad crossing created for the Lionel o-scale Fastrack system. Use superglue to glue the parts onto the track. Printing Instructions (Standard): I recommend PLA with 0.25mm layer height, <5% infill, 2 walls, and organic…
A small clip used to hold pieces of O scale Lionel Fastrack together.
Ich habe den Haltegriff auf der Fahrerseite meines Opel Astra durch ein klappbares Brillenetui für die Sonnenbrille ersetzt. Innen habe einfach etwas Stoff eingeklebt. Gedruckt in PETG Federn 0,7mm x 528mm x 8mm ( Amazon )
Astral Express ticket from the game “Honkai: Star rail”, for keychains, cosplay or badges. Just be sure to attach a pin or something similar.
Opel Astra H opc front bumper keychain
poklička pro alu kola na Opel astra F tisknuto v ASA pod úhlem 45°, majitel je následně bude lakovat. seděly na první dobrou :)
Tired of your trains running off the end of your track? Install these bumpers today. These bumpers are compatible with Lionel O scale Fastrack.
Astra J headlight cleaning system nozzle holder with the part numbers 13258411 and 13258412
Ash Tray Insert for Opel Astra H. I wanted to monitor the battery voltage and Coolant temperature in my Opel Astra H, so i designed this model to replace the Ash Tray with a nice little Screen to show me this information. I used this…
Air vent fins found in the Opel/Vauxhall Astra F. These models have slight modifications to the originals to make them print better. It is recommended to avoid PLA and print in PETG with solid infill. The “airVentBar” part is better…
Works with the original screw. Can be printed as is, without supports. Recommended print settings layer height: 0.15 mm infill: anything above 15% should do perimeters: 3 supports: no
A quick draft of the current Opel/Vauxhall Astra L with the step-File if you want to change something.
Opel/Vauxhall Astra G Sedan keychain from side view.
Adapter to put a BOSCH A 332 H flatblade wiper on my OPEL ASTRA J OPC. Prusament PC Carbon (fits best in color) / PC / PETG / ASA needs only a small support structure under the connection part to the arm.
This is a Lionel O-Scale 10in Fastrack straight section reference that I use for making track accessories. I have also included the sketch dimensions I used if you're curious. Find more of my model train prints in this collection , many…
This is a sleek window mount for the FasTrak Flex and Flex CAV with protruding passenger-count wheel. It is designed to work with (qty 3) 0.8" mini clear suction cups . Remove the velcro tape from your toll tag and then push the tag all…
This is a Phone Holder for Opel/Vauxhall Astra it has been tested and fitted on the K series 2016 model.
Cachas de la ASTRA Falcon 4000. Modelo liso sin dibujo, personalizable. Gun grips of ASTRA Falcon 4000. Smooth model without drawing, customizable.
A work in progress modular mounting system for Opel (Vauxhall) Astra H. This mounting system features modular design, so you can create your own things that you want to mount - cupholders, phone holders and so on. In my case I wanted a…
Maybe this fits other older cars, just try it. I can only say that it fits the Opel Astra H from 2007. Print in translucent filament. There is no need for supports, because the overhangs are small enough. You will have to transfer the…
As i drive as much as possible with the cruise control the rubber wheel is worn down after nearly 14 years and it was hard to adjust the speed with it. To change the whole expensive switch assembly you had to remove the airbag - so that…
Hello, it's me again. This time I'm bringing you a piece of armour from my armoury. Lower elements are identical on both hands. Forearm armour is connected with 30 mm elastic bands and buckles, as shown in the photos. Hand armour elements…
Habe hier einen Halter fürs Astra J 2010 Cockpit erstellt. Und einen Vorrichtung für´s IPad Air 2020.
This is a Opel/Vauxhall Astra G OPC keychain from front view. Good for people who love this car.
Used to hold the lambs nuts in place so they can be banded for castration. Just pull them down, slide the NutHugger over them to keep them down, then apply your castration band. Edges are slightly eased to prevent snagging
Ölfilterschlüssel Z19DTH Vectra C Astra H Meriva Erfolgreich getestet.
Starting this year's Pride Month with Vadrik, Astral Archmage Vadrik and his Husband Hailin who never shows up confirms the Church of Avacyn's support for Gay rights and the legality of Gay Marriage on Innistrad Happy Pride Month! If you…
This model lets you use the trunk light, or any replacement for it in your glove compartment. The original factory light is a faulty design, which has a switch built in, that is meant to turn the light off once you close the glove…
I made a new version of the wheel rim caps for my Opel Astra car. Printed with Prusa MK3 MMU2S and stell sheet Textured PEI.
My old sunvisor clips broke due to age so i made some new. Would recommend printing it in something quite heat resistant.
Adapter for the H7 Socket on the GM/Chevrolet Astra year 2000 or plus. If the LED gets loose in the adapter, i recommend to drill a small hole and screw a set screw to lock the led. LED Diameter: 16mm Based on the led: Shocklight S17
Ein Getränkehalter für alle Astra G Cabrio Liebhaber. Der Halter besteht aus 2 Teilen die leicht ohne Supports gedruckt werden können sie werden einfach zusammengesteckt und mit einer M5 Schraube fixiert. Funktioniert sehr gut und ist…
This Adapter allows you to use this strange small compartment in your Astra model Komm. My phone would not fit in this compartment, so I created this adapter to mount one of this MagSafe rings: Nillkin SnapHolder , they have adhesive on…
Prise USB pour permettre la recharge d'appareil
I created several coaster models based on this model. The rest are on my profile. I really wanted to print some Runescape themed coasters, but found that the models already out there were kind of bad. Print with 20% infill for best…
A remix of a lid for Sodastream glass bottles. In 2 colours with a 3D heart on the lid. Ein Remix eines Deckels für Sodastream Glasflaschen. In 2 Farben mit 3D-Herz auf dem Deckel.
A VR＋Rhino quick sketch of Astral Express for multi－color print
Found out there are many holders for this specific car, but none of them were actually fitting perfectly or solving my issues. I decided to measure the car, make a 3D scan of the hole and create perfectly fitted phone holder. And - here I…
---------- GERMAN ---------- Da mich der Anblick der Stabantenne an meinem Opel Astra K gestört hat und ich ohnehin überwiegend Android Auto nutze, habe ich diesen Blindstopfen kreiert. Auch mit dem Blindstopfen, hatte ich bisher…
This Antenna Grommet for the Opel Astra F (1991) is designed to replace the original rubber grommet of the vehicle, so that a new weather-resistant seal around your car's antenna is made. Tip - To ensure “weatherproofing”, you should…
Ich habe die Höhe des Halters modifiziert, sodass er die Getränke auch in Kurven sicherer hält. :) Original Beschreibung: Ein Getränkehalter für alle Astra G Cabrio Liebhaber. Der Halter besteht aus 2 Teilen die leicht ohne Supports…
The original Powerflex phone holder is not suitable for holding phones in thick cases like mine. This modification utilizes the back of the original Powerflex holder (Opel part number 13471402) and adds a new front. The front is printed…
Original Powerflex phone holder is unusable for holding phones in thick cases like mine. This modification uses back of original Powerflex holder (Opel part nr 13471402) and adds new front. Front printed from PETG. Front consist of two…
This is my Astral Elf Barbarian. This model was made for a fellow Patron of MZ4250 who requested it on the discord server that is available for every Patreon tier. A remix of a model made by MZ4250 ( Thingiverse Prinables ) . If you like…
Bovine talus (Latin: astragalus), used in Antiquity as a gaming die in knucklebones.
Astra logo contoured keyring with raised logo. Simple keyring that can be printed in single or multiple colours. Keyring is approx 2mm thick with a 1mm extruded logo making it light, sturdy and quick to print with minimal filament. For…
ASUS Astral 5080/5090 holder to support the card inside a Corsair 5000D case. The included holder by ASUS is way to long to fit in this Case. Without a holder this beast shouldnt be used to provide damage to the card and board. Variant A…
The Lionel Fastrack manual switches have a weak design for the switch stand and lever. It would last a 10 year old kid about 3 minutes before it is broken. I have two switches, both broken. I did order replacement stand and lever for them…
you need to scale it slightly. enjoy your keychain
