Counting matching models…
You can mod it to any other use, or to fit better in your car. Mine is Ford Kuga/Escape, but it is standardized interface, so it should fit in a lot of others. Just one note: slicer defaults to hiding the seam inside the hook, which is…
Introducing the ultimate solution for backseat boredom and mess! Backseat Foldable Table is the perfect accessory for any car, designed by me as a work in progress and research and development project. With its portable and easy-to-print…
This umbrella hook can hold up to two umbrellas on the back of your backseats in the car's trunk. Just make sure there are those tether points in your car (see photos), I think they are standardized - at least in Germany / Europe. Just…
This works now with an iPad Pro 10.5" (might also work with an iPad Air 2nd gen). It is a tight fit (especially if you try to slide it on on the camera side) but it shouldn't lose in the car. I recreated it as an one part print (you need…
This is a replacement for the backseat clip of Audi A4 B5. I didn't find the part number for it. Maybe some edits could be done to improve it, but so far it works fine for me. Comes with .stp and .stl Printed with Ender 3 V2 Print…
A tissue box with a flap to be fixed in the pocket of a car seat. I wanted a tissue box that wouldn't move when turning, accelerating or braking and that could be reached from any place within the car. Yes, it's easy to reach from the…
Hi 3D printing friends! This is a ball joint that fits the Skip Hop Baby Backseat Car Mirror. The ball is larger and more sturdy than the one that comes with the mirror, and has the ability to tighten and clamp down on the ball so it…
Traveling with children or passengers who crave entertainment on the go? Introducing this custom-designed 3D-printed holder for the Tesla Model Y and Model 3. Securely mount an iPad or phone using a magnet, ensuring the device is always…
I recommend PETG, but I didn't have any black PETG on hand so I printed it in PLA and it works. If it breaks, deforms I'll reprint in PETG.
Model Information After removing the backseats from our newly purchased Ford Tourneo Custom, I realized that Ford hasn't provided a cover to protect the socket hole in the floor from debris and potential damage. Even though the connector…
Need supports and needs string. How long the string is depends on how big your car seat head is. *DOES NOT WORK ON NINTENDO SWITCH LITES!!!
A single mirror is only sufficient for two toddlers on the backseat when it centered. That's possible using this model. Needs M4 nuts and bolts for fastening, as well as a plastic pipe. To be printed from sufficiently heat resistant…
Edit 2026-01-19: V3 with rotation feature. I've created a model of which you can rotate based per seat inclination. You can reuse an GoPro M5 thumb screw and a M5 nut to tighten the assembly. V2 model has a fixed angle. both models slide…
iPad Holder for Tesla Backset. Printed in two pieces. Assembly with one screw and nut. The plate does need support. Remark: The model is modified without Tesla logo.
Replaces GM 88937926 This part is no longer available online. This print will replace the clip that breaks often.
Designed to be printed with TPU. DO NOT PRINT IN PLA, EVER!. PETG might also work in a pinch, although has a high risk of breaking. I used Esun eTPU 95A, which has been working perfectly fine for over 3 years. After printing, connect via…
I made this 3. Seat Cover for a good Friend. I like to share it with this awesome Community. Let me know your thoughts in the comments.
I created a replacement lower arm for the backseat cupholder in my Nissa Xterra. Replacement uses the existing spring from original part. Original design is in 123D, but I will be recreating in openscad.
printed in PETG and fits verry tight
Backseat lighting house for Mitsubishi ASX (might fit other models) Just remove the backseat handles and use it's screws to put it in place *need to install a wire from the main light in the front to the backseat light is from ebay:…
If you lower your backseat, the original little plastic stopper can jam into the slot and putting back the seat to it's original position will be a pain. This piece solves that, it clips on top of the original stopper, there is no need to…
just a little cover up for the removal of the back seat bar
Smaller light for the backseat of Mitsubishi ASX Light link: https://www.aliexpress.com/item/1005003171890899.html
For older Chevy Suburbans with those spring-loaded push latches on the backside of the rear seats. Do not print in PLA. PETG or ABS/ASA would be best. Fusion 360 CAD files included.
frame and skeleton: tube printed with 0.1 10% motorcycle tail
I needed backseat mounts for my QX50 and wife's QX30. I liked the mount by hein0170 but didn't like the idea of having the headrest all the way up. Then I found Eckerput's headrest mount and printed both and assembled. However, the claws…
Road trips. Backseat Netflix. Data logging experiments. Whatever your mission, this headrest phone mount shows up ready to work. Designed for versatility and strength, this mount uses 9.5 mm diameter dowel rods (easily available at…
Design from OpensourceEV. Wanted to be able to mount a 20MM metal ball for a magnetic light. added space for the bolt
I combined a few existing models to create a clip to fix a mirror to the sun visor to observ the dog in the back seat.
Edit 2026-01-19: V3 with rotation feature. I've created a model of which you can rotate based per seat inclination. You can reuse an GoPro M5 thumb screw and a M5 nut to tighten the assembly. V2 model has a fixed angle. both models slide…
Need supports and needs string. How long the string is depends on how big your car seat head is. *DOES NOT WORK ON NINTENDO SWITCH LITES!!!
Road trips. Backseat Netflix. Data logging experiments. Whatever your mission, this headrest phone mount shows up ready to work. Designed for versatility and strength, this mount uses 9.5 mm diameter dowel rods (easily available at…
For older Chevy Suburbans with those spring-loaded push latches on the backside of the rear seats. Do not print in PLA. PETG or ABS/ASA would be best. Fusion 360 CAD files included.
![Car backseat pocket tissue box [no support]](https://media.printables.com/media/prints/899783/images/6881255_0ab22e4a-f762-43b2-b208-0c8b3a4b9416_e869d577-32e7-4ced-83d9-48c062c9121b/pxl_20240526_0510354673.jpg)
