Counting matching models…
The original VTX mount for the SpeedyBee Bee35 only supports the DJI Air 03 unit. The new 04 unit is slightly bigger and has a different location for the USB port. This design is based on the original CNC machined mount but modified to…
Replaces the stock GPS mount that comes with the Bee35 frame for use with the BZ-181 GPS module.
Hey, I got this great frame which was missing tail with dual antennas for my Walksnail setup, so I decided to make one, I used stock tail mounting options so it will be straight fit.
The Speedybee Bee35 frame comes with two options for the underside, where you mount the VTX - a single carbon fiber plate (basic version), or an aluminium CNC (Pro version). Neither fits the DJI O4 Air Pro properly unfortunately, because…
My SpeedyBee Bee35 came with a GPS mount TPU part for a smaller (I think 121) GPS module. I needed something slightly bigger, that also fits the specific connector geometry of the Walksnail WS-M181 GPS and compass module. In addition, I…
Want to use Geprc GPS M10-DQ or it's variation (22x22mm ) with Speedybee35 ? This is right model for it. Use FLEX materials because the gps must bee pushed into the chassis and there are 4 holders on the edges.
A simple bottom cover plate for the SpeedyBee Bee35 drone. This drone / frame comes with a CNC-cut aluminum bottom cover plate specifically designed for DJI O3 or similar-sized VTX modules. However, I was using it with an analog VTX…
SpeedyBee Bee35 front XT60E-M mount. Remove 2 nuts from xt60 connector, and insert them into slots in part with same orientation. This part allows to move high current battery wires away from magnetometer in rear GPS module. V2 is version…
Dual Antenna Mount for DJI04. with or without receiver antenna mount. I appreciate any feedback ! If you like this feel free to support me ( https://www.paypal.com/paypalme/NikaSte?locale.x=en_AU )
DJI Action 2 Mount für SpeedyBee Bee35 Whoop. Dieser Mount ist stabiler und zugleich leichter als das beiliegende Teil des Bee35, da hier keine schraube notwendig ist. Der Winkel liegt bei 25 Grad fix Am besten mit TPU A95 gedruckt, bei…
I liked the original design, but was a bit unstable due to the very thin wall, also not allowing to use of ND filters. You can use the holes to the top and bottom to secure the print to the camera using the same screw but is not necessary…
Print in TPU with organic supports and with little infil. Fits original screws. A little piece of 3M tape can be put to prevent Matek board from moving.
Here is my iteration of the Speedybee Bee35 Tail Inspired of different models but none totally convinced me, so here it is. Compatible with O4 Pro, BE-122 GPS module and USB C port at the back. Some glue may be needed for the USB port to…
Front mount for HGLRC M100 GPS (21x21), designed to sit in the GoPro position. Added a USB-C extension holder — I’m using an O4 Lite mounted on the stack, so this lets me access the port from the front without taking off the bottom plate…
Mount for Mateksys loud buzzer , just behind the camera. print with any material. Any feedback is appreciated!
A mount for your RunCam Thumb Pro for a SpeedyBee Bee35 frame. It replaces the GoPro mount TPU provided with the drone, and connects to the TPU cover that comes with the camera. Easy to Remix The STEP file contains two parts that can be…
UPDATE 4/29 - Test footage using this mount UPDATE - I have released a V2 version of the mount which features TPU vibration dampening. It is now a single unit adding strength and more protection to the camera. V1 - This enables you to…
Платформа под две антенны для DJI O4, тем, кто летает на SBUS. Использовать пластик TPU. Антенны надо будет подрезать. Маунт специально под укороченные антенны рисовал, чтоб уменьшить их травматизм. Добавил по просьбам трудящихся V2 и V3.
Нигде не нашел, решил сам нарисовать крепление разъема питания XT60E-M для SpeedyBee Bee35. Сам разъем просто приклеил суперклеем, хотя и так входит плотно. Крепление выступом и задним болтом. Печатал пластиком PETG.
This model weight is 2.5 gramm. It is connected to bee35 tail part instead of standart 12mm x12mm. TPU a95 was used to make this model.
