Counting matching models…
The Hybrid Betweener Tired of having to swap betweeners depending on the material you are printing and its ventilation needs? And where do I keep the spare betweeners when they are not in use? This project aims to provide the only…
Didn't like the idea of a big ol' hole in the lid of the K1 so I sealed it up and added a ptfe tube hole at an angle
This is a simple remix of a couple of betweeners to retain a hexagon pattern while still having a backdrop to “seal” it (as much as it can be sealed in this system). Print flat side down. Easy enough.
printed 15% infill Pla
Description I had issues with the rear betweener not fitting nicely because of the extruder cable. I made the gap for the cable bigger while also extending the wall on the right side so that it fully slots with both lid risers on both…
Added the capability of easy close vent. 100% Compatible with original model for Hinged Lid Riser Can print using standard PLA and standard 0.2mm parameters. Print Riser Betweener in vertical and add minimum support for slider section.
Creality K1 Hinged Riser Shutter betweener.
Was able to pint without support but you might want to add some in the void.
Designed a slidable air vent betweener that can be opened or closed. Remixed from a solid betweener made by Joe Cooper. This one has a slidable air vent that can be closed or opened. You can have the betweener closed eg. when printing ABS…
Tired of using a flashlight to see your prints? I sure was! Can be printed w/o support. Can print 2 at a time on the K1 if you are careful how you place them. Based on JCs excellent lid riser and hinge! Requires soldering etc… for the…
Back betweener that can be locked in the rightmost cable hole
This is a combination of an existing remix tool holder for the Ender series on Thingiverse and JC's Riser system for the K1. Added the proper supports/angles to ensure a snug fit, then tacked on a modded version of a Thingiverse remix by…
I found that the rear plate didn't fit the K1C due to the cable guide. So this is the rear betweener plate for the Creality K1 Riser design from Joe Cooper. Also, I made thinner Front risers, to avoid the printer head touching the risers.
Remixed SYSDmg design mainly to add space for 2 wires to go in the attended slots of the metal frame. It allows to avoid the printer carriage to catch one of the wire (the main wire, and in my case an USB cable for my Cartographer3D).…
print info. Rafts: No Supports: No Resolution: 0.2 mm Infill: 20% Perimeters: 2 Solid layers top/Bottom : 4 Material: ASA, ABS, PLA, PETG
I cut the slots to clear drag chain bracket
when using the lid riser which makes the bowden tube naturally bent and not pressed into the chain that feeds the cable to the head, I noticed that if we print on the left part of the table, the mentioned chain with the cable hits the…
wanted some slots for the rear Betweener so remixed and added slots
Removed 2mm x 41.5mm notch to allow betweener to clear the chain support
Suggest to rear panel standing with supports. Print with ASA or ABS or it will warp if you print closed with high temp.
3 Walls 20% infill no support, no brim
Made to work with the gap fill https://www.printables.com/model/918559-creality-k1-k1c-lid-gap-fill-top-cover-hole-close/remixes
Simple version for my need. A higrometer on Joe Cooper's awesome work
Remixed a slidable air vent betweener that can be opened or closed completly for the back of K1C. Details you can see on the original design description. Preconditions: JC Lid Riser:…
I've been printing more ASA and ABS, and lately venturing into PC. On top of maintaining chamber temperature, having a good seal to reduce VOC gas escaping into the printing room is important. The Problem The rear betweener has a gap for…
This is a betweener that incorporates a 45-degree ledge to stick an LED strip to. I have made a hole to allow the cable to exit if you want to use external power for the lights. I have one on each side, but you could use one or four. It's…
These tooth picks are really messy the have lying around. They do not stack, and is always a big mess. They kept on falling on the floor when I opened the door. 2,7 cm wide and 10 cm deep box. Box with compartments for each toothpick.…
I had an old roll of $5 bin led strip laying around and wanted to have a dimmable light with a red option so I could monitor prints at night without a glowing box in the corner. --Installation--(Described looking at front of machine with…
V1- DO NOT USE! unless you want to edit or physically remove the pattern towards the bottom of the betweener. Only use V2 as the original file did not allow for the unit to actually slide into place. The provided pattern protrudes to far.…
I wanted an improved rear in betweener that was able to close the opening of the lid and combat heatloss of the chamber
V1- DO NOT USE! unless you want to edit or physically remove the pattern towards the bottom of the betweener. Only use V2 as the original file did not allow for the unit to actually slide into place. The provided pattern protrudes to far.…
Was able to pint without support but you might want to add some in the void.
You might've noticed the small LED strip that comes in the K1 just isn't enough. You could always install a longer LED strip on the back face of the frame. It helps a lot but there will always be a blind spot kinda area behind the hotend…
