31 models
Build Instructions: Print Blobifier and optionally Brush Holder and associated Bucket-Brush, Install M3x2 Magnet into Bucket-Miller350, Install 4 Heat Sets into SB_Shaker_arm, Install the SB_Shaker onto the SB_Shaker_arm using 2 M3x8 FHCS…
Blobifier - Dropin adapter for Bambu silicone nozzle wiper kick out Brass Brush and dropin adapter for Bambu Silicone Nozzle Wiper Bambu Silicone Nozzle Wiper: https://eu.store.bambulab.com/products/heatbed-nozzle-wiper-a1 This is a…
More info on https://github.com/Dendrowen/Blobifier
A mod for the Blobifier mod that replaces the tray and servo arm with a rack+pinion mechanism to allow for a shorter base. Note: I'd recommend adding some plastic-safe grease to the rack and pinion interface to reduce wear and tear in the…
Voron A4T toolhead Blobifier shaker arm A modified version of the shaker arm and shaker to fit the A4T toolhead. Variations Against the Stealth Burner Shaker Design Redesigned the shaker to match the A4 toolhead geometry One M3x8 SHCS…
Modification of blobifier for Sovol SV08 Build of Materials: Servo SG90 or MG90 - 1pcs Switch OMRON D2F-5 (use NO) - 1pcs Magnet 6x3mm - 4pcs Screw M2x12 - 2pcs Screw M2x6 - 1pcs Screw M3x6 - 3pcs Heat set inserts (M3) - 2pcs Brass brush…
Just a simple bambu nozzle silicone brush holder that hovers over the blobifier bucket rather than the opposite side. It makes more sense for me to have it over the bucket to collect any left over filament.
Been working on this for a while on and off, pretty much has been working great for my setup. I had to change the files some to work for the standard bed layout for the 350mm 2.4 since my bed sits lower. Its also made for a 355mm and can…
A remix of the taller A1 nozzle brush for the Blobifier MMU purge system. Printing settings: Voron standard, vertical orientation
You don't need to feel frustrated about having to hand-pick strands or bits of filament from the bottom deck of your Micron printer anymore! You can instead, use these buckets (originally designed by @3DeezNutz ) but now in combination…
This shaker adapter should work with the standard Trident/V2 toolhead mount for dragon burner.
I have closed the shaker in by 2mm either side. Because of this mod, and the fact my toolhead was pushing the shaker back too far, I also extended the shaker arm by 5mm - this allows the Xol to sit back at 0 on the X axis when shaking. I…
AVISO: las alturas de la catapulta del cepillo y de la bandeja deben ser ajustadas físicamente ya que esta modificación se mueve con el pórtico en todo momento para ahorrar tiempo en cada purga. Por lo tanto es recomendable comprobar que…
1.The closing angle is 0 degrees, and the opening angle is 180 degrees as shown in the figure. 2.This design is suitable for converting voron or vzbot into trident. 3.I have provided the settings for the nozzle cleaning and waste…
Nozzle seal + silicone brush + blobifier standard mount
This is a remix on the the Blobifier bucket for use when you have a single fan “ The Filter ” installed. The magnetic wired mount interferes with the standard length bucket and doesn't let you snake it around the Blobifier servo. This…
the original 300 and 305 blobifier buckets where very short and filled up fast and would spread out good when shaking and i didnt like that! so i designed my own with a way bigger bucket and it also has a very very slight slopw towards…
Created a New Silicone Nozzle Brush holder, with a Small tray around it to catch those stray filaments and Blob's from the Blobifier that dont always come off.
Remix of horizontal z chain moving the mount to B drive to avoid collision of chain with blobifier Only compatible with IGUS chains Temperature mount can be found :…
I don't recall if I changed any other geometry, but this works with my LDO-spec 300mm bed perfectly. (Actual bed dimension is 305mm). YMMV. I intend to remove the decontaminator eventually and switch to its single pin sheet stop, but for…
We have found that cheap MG90/SG90 servo motors can die pretty fast from bed heat, therefore we developed the option to use a pancake stepper motor instead. This model uses a small GT2 belt as a toothed rack to move the blobifier's tray…
Modified with several changes. Mix and match to suit your needs - eg. use the servo arm for cheap 9g servos, use the OG gantry mount to mount underneath 2020 extrusion Gantry mount modified to be able to be attached to upright 2020…
The original version hits the gantry screws while printing. This solves it! I hope you like the models! If you want to support my work you can Buy me a Beer !
Adapted for PTK 7462W MG servo (better than MG90s)
Since I use the "breeze" auxiliary fan on my Voron 2.4, I couldn't mount the blobifier on the side. So I came up with another solution that can be mounted on top, doesn't require any "shake," and moves the blobs with a shield. The blobs…
this is my mix between blobifier, blobifier x and designed to fit a mercury zero g printer
The tabs which the MG90 sits on where pushed by about 2mm to allow for taller servos to be installed without bending the rack.
I have closed the shaker in by 2mm either side. Because of this mod, and the fact my toolhead was pushing the shaker back too far, I also extended the shaker arm by 5mm - this allows the Xol to sit back at 0 on the X axis when shaking. I…
Been working on this for a while on and off, pretty much has been working great for my setup. I had to change the files some to work for the standard bed layout for the 350mm 2.4 since my bed sits lower. Its also made for a 355mm and can…
