P
Printablesbb_prints
Blowtorch Base
No support required. The gas canisters are not very consistent in diameter. Some are a push fit, others will require an M3 screw tightened (not too tight!) against the can.
- Downloads
- 18
- Likes
- 3
- Rating
- 5
Search results: blowtorch
17 models
P
PrintablesDzR
HSW Blowtorch Mount
Crescent shaped holder to hold the Ernesto/Livarno EKB A1 blowtorch to the grid using a M4x16 screw to the "insert M4" base. You can use some sidecutters and a file to create two notches for the safety switches or use as is.
- Downloads
- 48
- Likes
- 12
- Rating
- 5
P
PrintablesFunbie Studios
Blowtorch for Transformers Legacy Gears
Here’s something of a specific tool which we see them minibots pull out from time to time in the good ‘ol G1 days – a blowtorch! Simply held in Gear’s hand, this makes it look like he has retraced his hand and replaced with with a…
- Downloads
- 39
- Likes
- 10
- Rating
- 0
P
PrintablesKingALLO
Gridfinity Blowtorch Lighter Holder
Hello Makers, I have designed this holder for my blowtorch lighter, so I can organise it with my other tools, that I also store within a gridfinity layout. With it being gridfinity, you can naturally use it with the baseplates and…
- Downloads
- 31
- Likes
- 3
- Rating
- 0
P
PrintablesAlly the Sentry
Mini Modular Gas Air Intake for D.I.Y. Furnaces and Blowtorches
FIRST OFF , thank you for checking out this model, I put a lot of time and sanity into it and I hope that it works with your needs! If you could like and download the model even if you aren't sure you need it, I would be very thankful,…
- Downloads
- 23
- Likes
- 6
- Rating
- 0
P
Printablesboidaboi
battlefield 4 blowtorch
prop of the bf4 blowtorch (bf3 and 6 as well). design in not great but i couldn't find one online so made one myself in a rush, thats why is so bad. build guide if needed included in files
- Downloads
- 21
- Likes
- 4
- Rating
- 0
P
PrintablesMcSail
Bench Vice Holster for Rothenberger SuperFire 2 Blowtorch / Torch
Perhaps a bit niche this one! Nevertheless, if you own a Rothenberger SuperFire blowtorch (a popular, quality torch) and use it with a remote gas cylinder, as I often do, then this could be very useful. When used with an integral gas…
- Downloads
- 3
- Likes
- 1
- Rating
- 0
P
Printables
Magnetic Wall Mount for Handheld Blowtorch
This wall mount attaches to any flat wall or wall stud using two screws. The mount has two recesses on the backside which accept center-bored magnets ( I used these ) up to 6.5mm deep and 35mm in diameter; while not strictly necessary,…
P
PrintablesFunbie Studios
Blowtorch for Transformers Studio Series 86 Brawn
Here's Brawn's blowtorch as a nod to an early appearance he made back in the pilot episodes! Designed for Studio Series 86 Brawn, he holds the blowtorch in his 'closed' hand like so. Of course, the tip of the blowtorch has been sized for…
- Likes
- 1
- Rating
- 0
P
Printables
Mini Blowtorch Base
Description I designed this years ago because I was tired of my mini blow torches falling over, and I put them right to use (while forgetting to share the file). I have used these on all my mini torches for years, and I only just realized…
P
Printables
Gridfinity blowtorch holder
This is a Gridfinity blowtorch holder. It can be used with the Gridfinity type magnets.
P
Printables
Magnetic Wall Mount for Handheld Blowtorch
This wall mount attaches to any flat wall or wall stud using two screws. The mount has two recesses on the backside which accept center-bored magnets ( I used these ) up to 6.5mm deep and 35mm in diameter; while not strictly necessary,…
P
Printables
Blowtorch stand
Base for a standard Propane/MAP cylinder blowtorch. Very useful and practical for keeping it from falling over.
P
Printables
Weller WT13EU blowtorch slider and trigger
Be careful when disassembling/reassembling the torch, to not break or leave gas lines open! The original internal slider part of the trigger broke on my blowtorch shortly after purchasing, after it fell off my desk. As I didn't want to…
P
Printables
Mini blowtorch Skadis/Skådis holder
This is a holder for a mini blowtorch to fit on an Ikea Skådis board. The tool faces you so as to occupy the minimum board real-estate. You will probably need to print with supports for the hook part. The hook exists as a stand-alone part…
P
Printables
Blowtorch holder 30mm for Skadis
This Design is meant for blowtorches with 30mm diameter. This is also a v2 (black in pictures) with 2 hooks so it is stable on the skadis plate. This design works great with hook from this guy:…