Counting matching models…
I purchased a used 997.1 this year and found the sound quality severely lacking after upgrading the old aftermarket head unit. Turns out the factory amp (ASK) had failed along with the stock woofers in the front doors. The factory woofers…
986 GT3 Center Console Delete The split file is to fit on a Prusa Mk3s Recommend using PETG Must remove orange tabs on the bracket to mount Left enough room to upholster part Fit as one part on Prusa XL. Used PETG with organic supports.…
Wanted to use a 4" Dayton Audio Full range speaker that i was familiar with. sounds great in the car. can use M4 screws directly into the plastic or use the version with M8 thread adapter version to increase mounting strength. Update…
3D model of the Porsche Boxster 986 and probably 911 996 frunk trim cover fastener. Porsche part # 999 590 036 40. Most of mine were broken or missing, so I remodeled them in CAD and printed my own rather than giving more money to the…
Porsche Boxster 987 convertible top transmission worm gears occasionally break due to age and/or excessive strain due to malfunctions. I have designed a replacement. Left and right gears are slightly different. Mirroring one gear in the…
If you've got a set of wheels that have somehow lost their centerpiece or the plastic tabs have broken off, then this Porsche Wheel Center Cap is a perfect replacement; Print as is or customize it with your own logo/text. It has a 77mm…
The windshield/wiper cowl on the Porsche Boxster (986) are notoriously prone to breaking. It's possible this may work for the 996 911 as well. When this happens the ends become loose and flap around and the cowl no longer makes a good…
Rear trunk emblem for a 986 Porsche Boxster
I went ahead and created new fonts and numbers for our Porsche 986 as the old one were long gone. This has been our fixer upper car and it was great to print a part that are as expensive as 80 euros. The print is pretty simple and is as…
Wall Art Silhouette model of the Porsche Boxster 981 Spyder. Adjustable size. I accept model suggestions or ideas.
Holder for bigger speakers for Porsche Boxster 986. Print with PET and 50% infill.
Needed to mount Alpine 8" woofers in the door of my 987 Boxster, So I made these…. can use M4 Sheet metal screws to mount the woofer to the adapter. Can cut the factory speaker basket to recover the plug that goes into the factory wire…
My car was missing a part and you can't get them from Porsche anymore. I put my own spin on the part and created own bracket to ensure the cabin air filter doesn't pop out of its housing. Uses the factory holes and a couple of automotive…
I modified the part by masticating_moose to fit a 3 inch full range driver instead of a 4 inch model. This will be installed as part of an aftermarket two-way system where i upgrade the tweeter in my 1998 boxster 2.5 installed with the…
This is a MagSafe phone mount designed to be used in the 991 / 981 generation Porsche 911, Boxster and Caymans. I was unhappy with all the phone mounts i found as the offset the phone to a spot i wasn't happy with. This puts the phone in…
In an effort to make myself and my wife as comfortable as possible on long trips, I designed and printed these clips that cling onto the sun visor and allow a 100mm (3.9") x 300mm (12") piece of 1.5mm (1/16") material ( hard plastic,…
I purchased a replacement for the overhead light on my boxster and the side clips which hold it in place were broken. It seems to be a common problem so this piece can be glued in its place and fulfills the same function.
Part#: 999-049-008-40
Simple sturdy intake port covers for Porsche 3.4L 9A1 engine head. These were in 2009-2012 Boxter S, Cayman S, and 911. Used these to prevent debris from falling in while working on the engine.
The anti-lock brake speed sensor and brake pad wear cable both plug into a common connector mounted just behind the brake disc on the Porsche Boxster 986. The goal of this build was to replace the connector housing, reusing the pins and…
This is the retaining ring at the bottom of the gear / shifter / shift boot for a 986 Boxster or a 996 911 and possibly later models. It fits my 2000 986 Boxster S perfectly printed in PETG at 0.2mm layer height, 100% infill. I rotate it…
Displaymodell von einem Porsche Boxster. Druckhinweise: Supports notwendig Infill 10% ausreichend am besten niedrige Schichthöhe
I created a Magnetic phone holder for my Boxster since I couldn't fine one I like. Since we are limited with space, I used the vent to hold it. Month later and is working fine. You'll need to buy the Car Mount from Amazon: Here is the…
Simple design to press the convertible top microswitch on the overhead console Could probably be tweaked to be a bit thicker but this still works. I tested it at highway speeds and it has no problems staying in place. I used it to force…
Models included are labeled R or L for right or left side of the car. The original clip incorporates a 11x10x3mm steel ring to support the area directly underneath the bolt that holds it in place. This replacement reuses that steel ring.
Reverse engineered from the original part, didn't recreate the bump pattern on top because it's too small for FDM printing. Maybe will add it in the future. This part doesn't fit perfectly just as an original part, I checked it on…
Reverse engineered from the original part, didn't recreate the bump pattern on top because it's too small for FDM printing. Maybe will add it in the future.
Tested on my R1200RS works perfectly to open the oil cap. You will find 2 versions: small, for a 1/4in wrench medium, for a 3/8in wrench Both fit the gridfinity bin, which is a 1x1x3u I printed the 3/8 adapter with 3 perimeters, 100%…
The multicolor is white with orange and black.
The HELIX Ci3 M100 loudspeakers fit into the door of the Porsche 987. However the chassis has mounting positions, that can be mounted in two directions. In the original position, the loudspeakers sit on the screw holes only - the chassis…
Wall Art Silhouette model of the Porsche Boxster 981 Spyder. Adjustable size. I accept model suggestions or ideas.
Mine was broken and wouldn't clip into the sun visor. So I modelled this part to superglue in its place and it worked perfectly. You will have to file off any excess plastic like I have demonstrated in the image. Then it fits snugly into…
Simple design to press the convertible top microswitch on the overhead console Could probably be tweaked to be a bit thicker but this still works. I tested it at highway speeds and it has no problems staying in place. I used it to force…
The multicolor is white with orange and black.
The HELIX Ci3 M100 loudspeakers fit into the door of the Porsche 987. However the chassis has mounting positions, that can be mounted in two directions. In the original position, the loudspeakers sit on the screw holes only - the chassis…
I purchased a used 997.1 this year and found the sound quality severely lacking after upgrading the old aftermarket head unit. Turns out the factory amp (ASK) had failed along with the stock woofers in the front doors. The factory woofers…
For any Porsche sports car owner who has fallen victim to Porsche’s notoriously impractical cupholders and suffered spills on the center console—this solution is for you. Should be compatible with: 911 from 2004/2005 (997 gen) to 2025, so…
Mine was broken and wouldn't clip into the sun visor. So I modelled this part to superglue in its place and it worked perfectly. You will have to file off any excess plastic like I have demonstrated in the image. Then it fits snugly into…
Print from at least PETG for the heat resistance. Sand the area that the part will be glued to. Sand the underside of the 3D print aswell for a strong bond. Use superglue. I tried 2-part epoxy but it didn't bond well to the Polypropelene…
If you want to get this template without subscribing, write me in chat! - SideSilhouette
