Counting matching models…
Needed a mount for some 1/2" PVC I got from ace. Used decimal inches because the imperial system is ridiculous and I refuse to use fractions when measuring things. Also I'm an engineer not an architect so decimals all day Customized…
Background: I was building a cart for my DeWalt 12 gallon Stealthsonic shopvac and found that the supplied hose for the duststopper was too short if I mounted it on top of the vacuum. This is a right angle (elbow) adapter for the shopvac…
Two different sized corrugated plate static mixers designed for use in 1-1/2" SCH40 PVC pipe. Category: DIY
I designed this case to attach the Flussmittelschorsch24 sensor board to my Landis Gyr+ E220 energy meter. I usually stick the magnets into my cases. But in this case I just fixed the magnets with adhesive tape. PCB: https://fms.lol…
A printed 6 inch SCH40 1/2 pipe for the nerf wye hopper. Was specifically made for the Piranha 2 Homemade. Print instructions Print slow use reasonable layer heights.
Material LEDs: https://www.amazon.de/AUKENIEN-Leuchtdioden-Leuchtdiode-Sortiment-Chartreuse/dp/B09TRHZCKV/ref=sr_1_8?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&s=industrial&sr=1-8 Motor:…
Needed some caps for a canoe trailer I was working on with 1" and 1-¼" SCH40 pipe supports covered in 3/8" wall insulation. Printed mine in ASA with supports (which are a pain to remove)
Thickened the inner wall around the thread. The original file I published cracked too easily when tightened.
Two models to connect 2in PVC to 2.5in blast gates (I used Powertec metal blast gates ). No special requirements for printing. Each end fits snuggly with a friction fit, but if you're fighting gravity you can use some hot glue for PETG to…
Simple holder for the remote control to a Farenheat FLCH4R garage heater. Probably fits other models too. Print standing up, no supports needed. Use whatever filament you want.
0.75" MNPT to 1.5" Female Socket SCH40 Adapter
Socket for the Chrager: 34x9mm Cable routing to the back minimal lengh of the wristband 11cm Additional holes at the bottom (was planned for some TPU feet, but i didn't made them)
This is a CH-47 Chinook coat hanger to hang over cubicles with glass dividers.
A Schedule 40 Pipe coupling with long inlet for telescoping to fit. Printed in Prusament PC Blend on Garolite. Designed for gutter water control and routing to rain barrels via 3" schedule 40 pipe.
These labels should slip over the bare end of US Sch40 NMC for ½‘’ and ¾‘’ pipe. Feel free to scale as needed, I included the Fusion 360 file with a sketch you can edit to scale for other size pipe or change the tag size. I used large…
Stampa con riempimento al 100% con un'altezza dello strato di 0.08mm e uno strato di base di 0.16mm Il modello ha una dimensione di 250x166.67mm Puoi stampare con altezze di strato maggiori al di sotto dello spessore di base di 0.48mm Lo…
¾" "SCH 40 PVC” plug for bulkhead in my overflow box Could be water tight not tested as where I am using is it is under water line on both sides in my overflow box in my reef tank.
I had a 1 inch pipe (nominal OD 1.3 inches) and the closest hole saw was 1.5 inch. I was building a large "lazy susan" built around a 1 inch iron pipe, I wanted it to fit tightly but my closest hole saw was 1.5 inches. but its a good…
Methane is the simplest hydrocarbon: a central carbon with four hydrogens in a tetrahedron (109.5 degrees). A labeled ball-and-stick 3D model for classrooms, teachers and chemistry fans. Every atom is a sphere in standard CPK colors with…
CH4 is the textbook tetrahedral molecule (AX4) with 109.5 degree bond angles. A labeled ball-and-stick 3D model for classrooms, teachers and chemistry fans. Every atom is a sphere in standard CPK colors with its element symbol plus proton…
Labeled ball-and-stick 3D model of Methanol (CH4O, also written CH3OH) - customizable in TrueGeometry Playground. CHEMISTRY Methanol is the simplest alcohol: one carbon, one oxygen and four hydrogens. The carbon is tetrahedral and the…
Simple yet useful accessory meant for epic Honeycomb storage wall that can be used for attaching Samsung Galaxy Watch4 charger. It has a fairly simple design and can be printed in about 30 minutes. It is mounted inside empty insert, which…
Cablebox which you can easily connect to the Sonoff. Originally designed for a product i made named PrintMeister. Cablebox which you can easily connect to the Sonoff. Originally designed for a product i made named PrintMeister.
Super Mario Bros. Charger for iPhone 12 (Pro) w/ case, Air Pods Pro and Apple Watch. I cut everything into pieces, to be able to fit them on the printer and also to avoid needing supports on any visible surfaces. So just glued everything…
This is a remix of the Samsung Galaxy Watch 4 charging stand by Maxime, which is a beautiful design but it is difficult to remove the charger once it is press fitted. Cropping off the top makes removal much easier; however, it loses the…
Redmi Watch4 Charging Stand base extends and the heavy base are connected by an M3 bolt and insert nut. heavy base used a 6402Z bearing as a counterweight. If you want to use something else as a counterweight, refer to the drawing
Simple case for USB to TTL module (CH340) from our favorite supplier Aliexpress. https://www.aliexpress.com/item/32831329095.html?spm=a2g0o.order_list.order_list_main.60.20051802o3CkKt Print Settings Printer Brand: Bambu Lab Printer: A1…
I modified the project to insert the Samsung Watch 4 charger which is larger than the iWatch one. Print with support and 15~20% infill
