Counting matching models…
My car has a very small space under the oil cap opening. Regular funnels did not seat straight without holding. The lower diameter of the funnel is 30mm which fits perfectly. The walls are 1.2mm which allows for both 0.4 and 0.6 nozzles.…
Took a model I had from a first gen and modified it to work in a 2nd gen CRV. Model has “CR-V” in the center that can be colored if you have a multi color printer.
Honda CRV RD1 Fender Flare Clip Category: Automotive
Designed for my 1997 crv. could work with others. sits in the rear light trim and is doublestick taped in. (3m foam tape) Changelog: V2: added a little strip at the bottom for better fit. Print Settings Printer Brand: Prusa Printer: I3…
I made this latch to replace the broken original one from my 1999 Honda CRV. It was made to be glued over the remaining plastic on the cable from the original latch. It fits with a small interference above it. The latch is to be pushed…
Windshield cleaner water cup replacement. Print with TPU.
These are cup holder inserts/ adaptors for a 1st gen CRV. Should be printed in ABS but PLA prototypes has held up well so far. No supports needed The taller one can have its outer diameter reduced by roughly 1mm for it to fit better next…
Manually copied the STL from https://www.printables.com/model/99035-car-seat-headrest-hook “Car Seat Headrest Hook” by M 3D in Fusion 360 and lengthened by approximately 22mm to fit seats in a 2025 Honda CRV Sport-L Hybrid. Close copy of…
Original rimcover were boring, so i created these ;)
A dummy key fob copy of a 2018 Honda CRV key fob. The model is not prefect but probably within .1 mm from the real key.
Made for my GF's 2006 CRV cup holders. They are super shallow and her Nalgene and coffee mug will fall out of them if she does any amount of accel/deceleration. Even a can of soda is pretty loose in them. This cup holder adapter press…
This was designed for my sister's 2007 Honda CRV. I think it would probably work for any 3rd gen CRV, so 2007 - 2010. This is an adapter so a Nalgene or Hydroflask, or similar sized water bottle can fit in the cup holder. The V1 model was…
Antenna / GPS Cover for honda CRV
Can holder adapter for a first Gen CRV. For 0.33l coke cans with 60mm diamater. (Standard EU can).
Fits a classic 32oz Nalgene water bottle in the center console of a 2015/2016 Honda CRV, using the smaller rectangular section of the console to not block the main cup holders when not in use. Print in the provided orientation with…
EDIT: Hey, this has been remixed, and the remix is better ! (Thanks D Rogers!) -Iggy. Just a cap that I whipped up for the above mentioned vehicle. I am 90% certain the oil change guy flipped the cap up, the retaining thingy snapped, and…
The source marked this model as adult content.
This is a center console organizer for a 6th generation Honda CRV Sport. Includes honeycomb slots for pens, cables and other small items, three larger pockets, and a "trash can" that can be lined with a plastic grocery bag.
Pieza adaptador tapa para surtidor limpia faros Honda CRV Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: Yes Resolution: 0,1 Infill: 90% Category: Vehicles
Modification for the Honda CRV cup holder to allow easier beverage display. Printed at 20 Percent Infill ABS should be used if being left in a Hot Car Printed on Ender 3
A while back I changed out the sway bushes on a 2004 Honda CRV. The replacement bushes I used were Urethane. However I had to buy generic ones and cut them down with a knife to make them fit, as there are none available here for this…
A faceplate fitting for a second gen Honda CRV, so i could fit my chinese double din radio. The brackets on the side are fitting the holes in the radio for better mounting. Feel free to use and modify.
This model replaces the L shaped part of the center console sliding lid on a 2017-2019 Honda CR-V. It removed the vertical section of the lid. It reuses the base and rubber pad. No original parts need to be modified. I used the fuzzy…
This part is for replacement of the interior door handle rod guide. Identified in the pictures by the orange arrow. Reinforced compared to the original. Easy to print, without supports. Three M3 hexagon head bolts and nuts are required.…
I was having trouble attaching the rear dashcam to the trim of my Honda CRV. This is what I came up with. On the rear wing of the wedge I put some ¼ inch adhesive backed foam to help keep the camera in place as well as absorb shock while…
Honda CRV Door Grab/Handle/Arm Rest Clips The clips that the door grab gets screwed into. works on all 4 doors, both front and rear clips for each door. I printed them in ABS and they have held up fine. Make sure you clean up the hole the…
I made this quick little key chain so I could identify which keys were for which vehicle I had after grabbing the wrong keys before leaving 1 too many times. This model is made in such a way that swapping the filament at a specific layer…
Front Main Seal/Crankshaft Seal Driver for the first generation Honda CRV RD1. Printed in 3 parts so you don't need supports. Part 1 and 2 lock into each other and then part 3 is slid into part 2. You can use something to tap part 3 down…
This model is for a shelf that sits above the sliding lid on a 2020-2022 Honda CR-V center console. The sliding lid moves under the shelf eliminating the need to remove items under the arm rest to open the compartment. The height is…
Football Klub Crvena Zvezda Belgrade
A simple pen holder for the Cricut Personal CRV001 Cutter machine allowing use of a variety of pens and markers. I use this holder with the popular PILOT G-2 07 pen. By unscrewing the pen body I can set the pressure of the pen tip to the…
Seal Driver No supports Part 2 gets attached to Part 1
This goes in place of the dash clock or blank plate for some models. It mounts in exactly the same way as the clock or blank plate do and can be paired with any AMPS mounted system. Recommended that you print it in PETG or ABS/ASA with 4…
The temperature control dial cover broke on my moms 2013 Honda CRV, so this was made to cover up the bright light underneath.
Extended Fog Light Housing to fit China Led in it. I used OEM like DEPO fog lights. Can anyone confirm that these also fit OEM fog lights. The spacer goes between the bumper and the fog light. The small notch is on the inside facing…
On a 2004 Honda CRV, there is a screw on plastic ring that holds the fuel sender down. The top of the ring cracked and let the sender pop up and get fuel everywhere. I was able to design and print this part before the part I ordered…
Replacement fender flare clip for Honda CR-V. Fits first-generation models from 1997 to 2001. Replaces brittle or broken OEM plastic retainers. Restores your exterior wheel arch molding securely. 🛠 Print Settings Material : PETG Infill :…
This is a useful 50mm deep tray that replaces the garbage QI charging pad in a 2021 Honda CRV Hybrid Touring. May fit similar models, but I'm unable to test that. Simply pop up the center console, unplug the QI pad and remove the 4 screws…
Back Rear Windchill Cap
working on a first version prototype Honda CRV TRUNK NET HOOK attachment.
Designed specifically to adapt the cup holder of a 2012 CRV to fit large diameter Yeti cups and smaller energy drinks. Has a separate bottom piece designed to be printed in TPU and then glued to the body of the cup holder.
Recommend printing in PETG or PCTG, especially in hot climate. Stacking design.
switch blank for 2002 Honda crv I used it for my Kings light-bar switch Recommend Printing with internal brim fits loose before switch is installed
A flip-up cover for the reverse switch a 2021 Honda CRV. It should fit others as well. Print using supports. Use m2 screws to connect the hinge Attach the bottom part to the card with 2-sided tape
EDIT: I installed these and they lasted like 3 days in the summer, i will revisit this, but for now I'm just leaving the key caps off as they still work without, just not very pretty... This generation of plastic horn buttons is getting…
sturdy and strong case
Print with TPU, mine is printed in Sunlu TPU 95A and fits perfectly It is inspired by this cap: https://www.printables.com/model/723302-honda-crv-2nd-gen-windshield-washer-reservoir-cap although it is not a remix. It was made from…
Built this specifically for the 2026 CR-V, but honestly, you could stick it anywhere. It puts your phone right next to the screen for a clean look. Just use some double-sided tape to pop it onto the dash. It uses a 17.2mm ball, so it’ll…
PETG definetly recommended. PLA deforming due to temperatures in car. Don't know are this size magnets wide available, I used one from mine old, broken holder. But you can take this as an idea and create yours, with prefered dimensions :)…
This is a cup holder for the 2016 CRV to accommodate a YETI 14.5oz Rambler. I also used the top portion from a model on Thingiverse HERE .
This is the first 3D model I’ve published on this platform. I searched high and low for this part online but couldn’t find it. Finally, I decided to design it myself and put it to use.
This model replaces the L shaped part of the center console sliding lid on a 2017-2019 Honda CR-V. It removed the vertical section of the lid. It reuses the base and rubber pad. No original parts need to be modified. I used the fuzzy…
This model is for a shelf that sits above the sliding lid on a 2020-2022 Honda CR-V center console. The sliding lid moves under the shelf eliminating the need to remove items under the arm rest to open the compartment. The height is…
This is a center console organizer for a 6th generation Honda CRV Sport. Includes honeycomb slots for pens, cables and other small items, three larger pockets, and a "trash can" that can be lined with a plastic grocery bag.
working on a first version prototype Honda CRV TRUNK NET HOOK attachment.
Built this specifically for the 2026 CR-V, but honestly, you could stick it anywhere. It puts your phone right next to the screen for a clean look. Just use some double-sided tape to pop it onto the dash. It uses a 17.2mm ball, so it’ll…
EDIT: Hey, this has been remixed, and the remix is better ! (Thanks D Rogers!) -Iggy. Just a cap that I whipped up for the above mentioned vehicle. I am 90% certain the oil change guy flipped the cap up, the retaining thingy snapped, and…
Extended Fog Light Housing to fit China Led in it. I used OEM like DEPO fog lights. Can anyone confirm that these also fit OEM fog lights. The spacer goes between the bumper and the fog light. The small notch is on the inside facing…
