Counting matching models…
Nicer Dicer Gitter / Nicer Dicer Grid Gitter für Nicer (nur das Gitter, nicht der grüne Einsatz) TIPP: sehr langsam drucken. max 30mm/s Grid for Nicer Dicer (only the grid, not the green insert) Tip: very slowly print with max. 30mm/s…
A tray / organizer for all your Genius Nicer Dicer Chef accessories. Took a whole day to print mine, but my printer ran out of filament, so on my photo the print isn't finished 100% :-). But it worked good enough, so I kept my failed one.…
I have more than the standard accessory which where included in the basic Nicer Dicer Chef set. So I need a bigger organizer.
Nicer Dicer Magic Cube grid replacement part. An easy to break part that can be replaced easily many times if needed. Simple object designed with Openscad. I also included a Fusion360 and STEP version. No special tips for printing, my…
Passt gut! Vielen Dank an "NorMaker"!
Chasmosaurine fromthe Judith River Formation.
Earliest Chasmosaurine from the Judith River Formation.
Funktioniert sehr Gut. Vielen Dank an "DAVIDM84"!
Remastered version of Wendiceratops, now in 2 poses.
A replacement for a broken Nicer Dicer clip. See photos. Clip can be a bit tight.... OpenSCAD file included! UPDATE I redesigned the inner slot, so the clip should move more comfortably now. Let me know what you think about it. Enjoy!…
Print in PLA or PLA+ with the hinge axis pointed up. Tab is meant to be snug and might require some light sanding along its length. Will fit some aftermarket turntable covers (from company Open Format).
the diceratops has 2 horns on its face
Ceratopsian from the Oldman Formation.
The holders for the container always break. So far, I have always bought a new one, but I don't want to do that anymore. So, I have designed and tested this model. It fits perfectly on the small Genius Nicer Dicer onion and vegetable…
The top of my cheap dicer bought on Amazon (branded as "Lyizci") broke after the 3rd use (link amazon https://www.amazon.ca/Vegetable-Chopper-Mandoline-Container-Choppers/dp/B09NLS4B51 not affiliate, just as a ref to see which model I'm…
Print recommendation is in ABS as the nicer Dicer is also made out of ABS but i think PLA should work too.
Ersatzteil für Verriegelung – Genius Groß Zwiebelschneider / Nicer Dicer (Modell 33087) Ich habe ein passgenaues Ersatzteil für die Verriegelung des Genius Groß Zwiebelschneiders (Modell 33087 / Nicer Dicer) entworfen, da dieses Teil oft…
Standard Replacement Bowl for Genius Nicer Dicer Chef. Printing with PETG works pretty well.
Abmessung: komplett ca. 131x158x141 mm Filament: PETG Perimeter: 4 Düsen-Ø: 0,6 Infil: 20 Druckprofil: 0.20mm Balanced Filament-Bedarf: ca. 560 gr. Gesamt Gedruckt wird der Boden 4x, jede Seite und die Rückwand je einmal. zusätzlich…
Simple replacement bowl for nicer dicer magic cube. Original lid fits the bowl. Design optimised to print without supports. Just small clean-up required for the briged areas to make the lid-clips snap perfect.
This is a replacement part for the Nicer Dicer Magic Cube. Important: This is not the default grid, only applies when you buy the extension to have a full cutting area. See my other design to get the usual grid replacement. I should have…
This is the Dicer 9000. It is made to make dicing a bit more dicier ;). Its easy to Print in under 3H. To have good results with the Tower you have to print it upside down. For comparison, my dices are 16mm long on each side and i would…
After my wife cut her finger, fiddling the knife insert out of the plastic bag, she asked me to print a protective sleeve for them. A bit of modeling later and after I also cut one of my fingers, it was done. Printed with: 0.6 mm nozzle…
