P
PrintablesPaetthe
Topping DX3 Pro+ bracket
I printed mine in PETG, lying down on the side (the one with the “X”). I used double sided tape to mount it, but you can use the screw holes as well.
- Downloads
- 116
- Likes
- 13
- Rating
- 4
Search results: dx3
Counting matching models…
P
Printablesludodg
Spektrum DX3R battery door
Very simple really The battery-door of my old trusted Spektrum DX3R-radio had a little lid broken of and did not held tightly anymore. I found another STL for a DX3 … but that radio did not havge the same dimentions, as I noticed after…
- Downloads
- 86
- Likes
- 1
- Rating
- 0
P
PrintablesMike81622
Spektrum SLT3 / DX3 Smart Transmitter Wall Mount
Wall mount for Spektrum SLT3 RC car transmitters, that come with lots of Arrma RC cars, e.g. Senton, Granite 223s, Kraton, Typhoon, Big Rock, Mojave, ... Will also work with Spektrum DX3 Smart transmitter, since it's the same shell as the…
- Downloads
- 63
- Likes
- 3
- Rating
- 0
P
Printablesludodg
Spektrum DX3E battery door
Very simple really The battery-door of my old trusted Spektrum DX3R-radio had a little lid broken of and did not held tightly anymore. I found another STL for a DX3 … but that radio did not havge the same dimentions, as I noticed after…
- Downloads
- 58
- Likes
- 0
- Rating
- 0
P
PrintablesKage
Topping DX3 Pro+ Under Desk Mount + Cable Holder
This is a suppot to hang the Topping DX3 Pro+ under the desk with double sided tape. No holes added because i wont drill it in. There is space to fit the Remote over the DAC with the mount F3D Files attached as well.
- Downloads
- 57
- Likes
- 4
- Rating
- 5
P
Printablessirromeoj
Topping DX3 Pro+ bracket (remix)
Remix of Topping DX3 Pro+ bracket by Paetthe (https://www.printables.com/model/811508-topping-dx3-pro-bracket) I added holes on the other side of the bracket to make it easier to mount using screws. Simply hold the amp and brackets…
- Downloads
- 30
- Likes
- 1
- Rating
- 0
P
PrintablesRake
Topping MX3s, DX3Pro+, PA3s Mount Kit
A complete kit to mount the Topping MX3s Amp+DAC, Remote and Power Supply neatly on the underside of your desk, or anywhere else you'd like to put it! Other Topping Amps / DACs These parts were designed for the MX3s. However, some parts…
- Downloads
- 29
- Likes
- 3
- Rating
- 5
P
PrintablesAlu
Topping DX3 Pro under table holder
Mount the holder with wood screws or tape, slide DX3 Pro from the front until flush. The part is designed in a way that the feet don't interfere.
- Downloads
- 21
- Likes
- 1
- Rating
- 0
P
PrintablesStartrekfan2
Handle for CAT DX37 angle grinder
This is a modification of Ian_Makes ' Angle Grinder Handle - M10 Bosch . I am using PrusaSlicer's negative volume modifier to reduce the flange diameter. The CAT DX47 uses the same M10x25 bolt and nut, but the flange diameter must be…
- Downloads
- 21
- Likes
- 10
- Rating
- 0
P
Printablesludodg
Spektrum DX3E Antenna Holder
The antenna on my old Spektrum DX3E broke off. I found a new antenna-top-part on thingiverse: … https://www.thingiverse.com/thing:2755370 But it seemed also the bottom-part, housing into the radio was somewhat damaged .. AND it was…
- Downloads
- 19
- Likes
- 0
- Rating
- 0
P
PrintablesSzwalkiewicz
Spektrum DX3
For Spektrum DX3 to replace ageing foam wheel with 1/10 scale touring car tire Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: Yes Resolution: .2 Infill: 100 Filament: amazon PLA Gray Category: R/C…
- Downloads
- 17
- Likes
- 2
- Rating
- 0
P
PrintablesDennis Calosso
GPU Vertical Holder For PC Custom Loop (Bykski N-ICH5090DX3-X Block + BeQuiet! Light Base 900DX/FX Case)
this prints allow you to create a GPU vertical holder for a Bykski N-ICH5090DX3-X Block in a BeQuiet! Light Base 900DX/FX Case, configured with a 28-30 mm thick radiator on the bottom of the case and a 25 mm thick fans on top of it,…
- Downloads
- 13
- Likes
- 0
- Rating
- 0
P
Printableszram
Topping DX3 Pro+ Desk Stand
A desk stand for the Topping DX3 pro+ with a lip for a speaker on top and a hook on the side for earphones.
- Downloads
- 7
- Likes
- 1
- Rating
- 0
P
Printables
Topping DX3 Pro under table holder
Mount the holder with wood screws or tape, slide DX3 Pro from the front until flush. The part is designed in a way that the feet don't interfere.
P
Printables
XL Nextruder 5mmODx3mmID Bowden Tube
Update 5/3/24 Added modified filament sensors with magnet modification for lighter drag on the filament. Uses 4mm diameter magnets. At elevated temperatures found inside an enclosure, the 4mm bowden tubes tend to kink or become a source…