P
Printablesveikus
Picatinny rail flashlight mount (Nitecore EC20)
Mount for a Nitecore EC20 flashlight (21mm diameter). You will also need: 2x M3x30mm bolt, 2x M3x12mm bolt, 4x M3 nut
- Downloads
- 510
- Likes
- 71
- Rating
- 5
Search results: ec2
Counting matching models…
P
PrintablesGuardTower
Portafilter Scale stand for Delonghi Stilosa EC230 or EC260 V2 for N600 Grinder
I am using a cheap N600 generic flat burr grinder and the V2 is designed to slot the bottom side of the plate against the bottom bar
- Downloads
- 133
- Likes
- 13
- Rating
- 4.5
P
PrintablesEngScott2076
UPDATED 29Dec2024: Gridfinity Storage Cover(s) - Configured in Fusion 360
UPDATED: 29Dec2024: Per request by @ThiDav_2532052 (Good suggestion, thank you) , I added a version with a raised handle to more easily get your fingers on it. This new version does not allow for stacking since the top of the cover is no…
- Downloads
- 110
- Likes
- 6
- Rating
- 5
P
PrintablesGuardTower
Portafilter Scale stand for Delonghi Stilosa EC230 or EC260
A simple stand to put your portafilter on when measuring preground coffee straight to the portafilter. It can also be used for distributing, tamping, or just putting your portafilter on standby. The holes are also high enough that the tip…
- Downloads
- 93
- Likes
- 11
- Rating
- 0
P
Printables3DPrintDesigns.it
De'Longhi EC260 Replacement Knob (Reinforced Version)
Project Description This is a replacement and improved control knob designed for the De'Longhi EC260 espresso machine. Many original knobs tend to break over time, especially at the mounting point on the back. I modeled this knob to be a…
- Downloads
- 90
- Likes
- 1
- Rating
- 0
P
PrintablesDom's 3d Print Shop
De Longhi Ec201 Espresso Machine Accessory holder
Easy to use and print. Highly recommended to print it in PETG, so that it can be cleaned in a dishwasher. Printed with 3 perimeters and 10% infill.
- Downloads
- 20
- Likes
- 8
- Rating
- 0
P
PrintablesDrgigaherz
Aprilia RSV4 Crashprotection EC2.0 connectors frontfork
I've had 2 crashes now on track. Both times the vulnerable connectors were destroyed which can be a pricey replacement. I printed these parts lying down with PA12-CF with 4 perimeters and 50% infill 0,1 layer height, support needed i…
- Downloads
- 13
- Likes
- 3
- Rating
- 0
P
PrintablesIonRoux
EasyPro Eco-Clear EC2600/U filter ball holder
These pond filters come with bio balls that hang out at the bottom of the chamber. There is a plastic disc that goes over them, but it has large holes in it that the balls fit through. If you pull the filters out to clean them, your balls…
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesOexyz
Eyecatcher EC200 replacement clip
The replacement part for the Eyecatcher EC200 from Grass Valley costs around 45€—daylight robbery! Printing it myself on my Ender 3 uses just 6g of filament and takes about 6 minutes, making the total cost of the print roughly 6 cents. A…
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
PrintablesCyrus
Printables Bookmark Design Contest entry Dec2022
This is my bookmark entry for the Printables Dec2022 design contest. It can be printed as 1 color or multi-color. To print multi-color switch the filament at the beginning of layer 6 using 0.20mm layers. The letters stick out thus holding…
- Downloads
- 9
- Likes
- 0
- Rating
- 0
P
PrintablesRex
DeWalt DXAEC2 Battery Tender/Charger/Maintainer Wall Mount
This is a wall bracket for the DeWalt 2 Amp DXAEC2 Battery Charger and Maintainer that swivels on a hinged mount to facilitate viewing the charge status indicators from across the garage. The vehicle is not a daily driver so checking…
- Downloads
- 5
- Likes
- 2
- Rating
- 0
P
PrintablesAudiotec Fischer GmbH
Audiotec Fischer EC2.0 stand
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
- Downloads
- 5
- Likes
- 2
- Rating
- 0
P
Printablesderek3d
Samsung Center Speaker PS-EC2-1 Mount
Mounts my center speaker under a TV and is reversible. I made it so that the same bracket is used for the left and right side. Printed in PETG with extra walls. Has been up for a month now with no problems.
- Downloads
- 4
- Likes
- 0
- Rating
- 0
P
Printables
Audiotec Fischer EC2.0 stand
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
P
Printables
HP ec200a stacking stand
A slip on stand for stacking hp ec200a's leaving a good amount of space for airflow. I printed in pla and then pulled it over the rubber feet on the servers. I have put air vents in the model but i would recommend not covering the cpu…
P
Printables
Godox AD200 - EC200 to AD-E2 Mount Adapter
The stock AD-E2 mount is not directly compatible with the EC200 extension cable head, so this adapter allows a secure mounting. Should be compatible with other cold shoe devices (not tested) Printing tips: No supports required Infill…
P
Printables
Wall hanged Portafilter station for Delonghi Stilosa EC230 or EC260
The station is fit for the 2ear stock portafilter of the delonghi stilosa.