Counting matching models…
Harb is a small excursion steamer that fills both in the harbour and in the lakes of this world at home. What he doesn't like is the rough, open sea. High waves can make him capsize due to the high centre of gravity. Since you don't have…
I printed this in Petg-CF with 4 walls at 20% infill. This can be printed as a single piece or in 4 pieces to save filament since you wont have massive support structures. Make sure your printer is dimensionally accurate. It will be a…
This is printed from carbon fiber petg. 15% infill, 2 walls on the bottom piece and 4 walls on the top piece. They will snap together pretty tight when finished. Just use some adhesive of your choice in the groove. I personally use…
I took a while to get the geometry more-or-less matching to replace the bag hook/ash-tray for these trucks. I'm currently using mine to mount a Yaesu FTM-150 dual band amateur radio, but I've included the blank mesh, and step files for…
05-07 Superduty style fender emblem for a Ford Excursion Limited. Colored to show contrast. Would be ideal to sand smooth then paint desired color.
Tello Lunar Excursion Module (LEM) UPDATE* When I first test flew this it didn't have the Nozzle in place. After attaching it I discovered it interferes with the Tello's altitude and stabilization system so it needed to go. At the same…
Courtesy/ door light cover for Ford excursion, printed in translucent PETG
Ein Dosenhalter für das Kajak " excursion k2 " von Firma INTEX A can holder for the kayak ‘ excursion k2 ’ from INTEX Design noch nicht getestet. Wird in die Halterungen für die Kamera- und Angerutenaufnahme gesteckt. Sollte passen :)
Cover the face of the 2020 excursions on the delta flyer refit by Rolohaun
This fixes your loose or worn out rooftop AC vents
Replacement jack cover retainers. Print at a 45 degree angle with normal (Snug) supports. adaptive layer height set to the smoothest setting. 3 walls. 4 bottom layers 6 top. I would suggest printing out of PETG-CF, ASA, or ABS.
Bonjour, voici un attache pour le kayak intex excursion k2 et k1 a mettre a l'emplacement des porte canne afin de pouvoir y incruster des porte canne plus pratique. Hello, Here is a clip for the kayak intex excursion k2 and k1 to put in…
This little LEM tribute model is fun (and fragile) to fly. Video Because it's based on the TXD-G1 mini drone it will only give you a couple minutes of flight time. I'm going to try it with the non-camera version to see if the flight times…
For assembly you need Metal pipe 12-12.5 mm thick Bolt M5 15 mm (2 pcs.) Bolt M5 35 mm, can be longer (2 pc.) Bolt M4 20mm (4 pc.) Nut M4 (4 pcs.) Nut M5 (3 pcs.)
This is a twist lock for the jack compartment in the cargo area of a Ford Excursion. Some of the geometry has been modified to eliminate the need for supports in the center of the model. You will still need some supports for the tab and…
About three times a week, I like to leave my home and go for a quick jog around the area. It clears the mind, strengthens the body and my scant little loin cloth is a big hit with the ladies. The thing is... that's pretty much all I'm…
Rubber stoppers on my excursion were trash so i designed this "plug" looking thing to get the stance of the fuel door correct again. Printed in TPU with few walls and low infil time will tell but pops into place and holding up well now…
If you use Cura for your slicer, print this at 150% size so it can fit onto a keychain.
Rubber stoppers on my excursion were trash so i designed this "plug" looking thing to get the stance of the fuel door correct again. Printed in TPU with few walls and low infil time will tell but pops into place and holding up well now…
