Counting matching models…
Ich vbrauchte für unseren Opel Rocks E einen Innenspiegel. Diesen habe ich bei Amazon gefunden. Der originale Halter des Spiegels sagte mir nicht so zu, da man ihn hätte Schrauben oder Kleben müssen. Also einen neuen konstruiert. Infill:…
V2 UPDATE: Ok, so i had a brainfart while "CADing" this and made it too tight for no reason at all. Now it should fit MUCH BETTER. The clip has identical dimensions to the original and the same function. The only thing that i could not…
Original document holder must be modified. Use double side tape (or glue) and 4 screw for each side. Print twice (one mirrored) It is for 7 inch 1din radio. Might be used for 2 din (I didn't try it)
This ceiling light clip is originnaly a metal part which often causes short circuits in the car so i made a new one . I used ABS avec printed it vertically. You can stick some aluminium tape in it to reflect the light
These tools can be used to fix the camshaft on MultiAir engines and the crankshaft on T-Jet and MultiAir. This makes it easier to replace the timing belt. There are two versions for the camshaft. The version without a pin allows you to…
Capture the spirit of classic Italian motoring with this 3D printable STL model of the Fiat 124 Spider. This charming convertible model is perfect for automotive enthusiasts looking to display the iconic design and open-air freedom of…
Bring a piece of Italian automotive history to your collection with this 3D printable STL model of the Fiat 500. This iconic city car model is perfect for enthusiasts of classic European vehicles, offering a charming and stylish addition…
Embrace the charm of a bygone era with this 3D printable STL model of the Vintage Fiat 500. This classic Italian city car model is perfect for automotive enthusiasts and fans of iconic European retro vehicles, offering a beloved piece of…
Frame sostitutivo per la cuffia della leva del cambio della Fiat Panda 141. Stampare in Petg o altri materiali resistenti al calore. Assolutamente sconsigliato stampare in PLA. 3D printable replacement frame for the Fiat Panda 141 gear…
I wanted to add a touch of classic, vintage design to my living room above the sofa. I redesigned the front end of the original 1960s Fiat 500 and created a unique wall decoration. It creates a personal, unique effect that will amaze your…
12/19/25 update to release V2 based on feedback from an owner of the JO/EL intake: -Changed the cutouts under the venturis from spherical to conical. -Changed engine side venturi cutout diameter from 36mm to 37mm. -Changed non-engine side…
Recreation of the spark plug wire holder. Probably fits other cars that use the 999 FIRE engine. Works well printed in Nylon by JLC3D. Simplified the attachment clip and replaced it with a friction fit.
Fiat 124 (1976) / Murat 124 – STL release Single-piece, watertight mesh. Scale as needed in your slicer (STL has no units). Feedback welcome.
Rear Door Handle Fiat Scudo / Citroen Jumpy / Peugeot Expert OEM 9408720738 - Maniglia Interna portellone posteriore Two Versions: Standard / Lite MANIGLIA INTERNA SERRATURA PORTA PORTIERA DESTRA PARETE POSTERIORE FIAT SCUDO FIAT…
Uchwyt pasuje do kubków na napoje do 0.5 litra oraz z puszkami 0.33 i 0,5 litra
Design Concept This 3D model is the air vent for Fiat Grande Punto or Linea . It is designed with precise dimensions to ensure it fits seamlessly into the existing dashboard panel of these vehicles. Purpose The model serves as a…
Gauge pod for Fiat Linea / Grande Punto. For the driver's side air vent. The pod diameter is 52mm. I added the SCAD file so you can edit it if you want. I added the T-Jet text in the bottom corner, but it is not in the files. Have fun!
Fiat Linea keychain. I printed it myself from TPU, but PETG and PLA will work too. I added "No More Grey"- slogan for my own and you can add a slogan / text for your own.
a simple clip to replace a broken one on your fiat 500x (tested on 2018 model)
Stencil to align the crankshaft when doing the timing belt. Amazon tools accuracy was awful so I did my own.
Fiat 126p Maluch Cookie Cutter Didn't find what would interest you? Let's create your dream project together. Write to this email : ----> [email protected] <----
Bumper plug. Peugeot Boxer, Citroen Jumper, Fiat Ducato
Printed it with Mk4s PETG. No Support needed. I used 0.6mm Nozzle but should be no problem with everything else. 15% infill is enought.
Fiat Croma hood rod clip, a little tight but you can fit it with pliers
I printed it in two colors on the Creality HI. Printed with standard supports under 45°. I then simply glued the part on using regular transparent silicone.
Portachiavi "Lingotto" - Edizione Grande Panda Porta lo stile della nuova icona italiana sempre con te! Questo portachiavi è ispirato alla celebre forma a "ovale allungato" della pista del Lingotto, richiamando il linguaggio stilistico…
A good friend asked me to help fix a broken clip. I traced the outlines in Fusion 360 using a scaled photo. The teeth could be improved, but they get the job done!
Handle designed for the seat swivel lever used in motorhomes based on Fiat platforms. The model is a modified version of a design available on Printables (“Fiat Motorhome Driver Seat Lever”). Structural changes have been introduced to…
Jde o zakrytí matic v prostoru pro nápoje (plechovky), aby tam nepadal bordel. Originálně jsou tam gumové podložky. Ty už tam bohužel nemám, tak jsem si dodělal vlastní. Ty údaje jsou tam přidaný ze srandy.
Dieser Schlüsselanhänger passt perfekt zum Originalen Fiat 500! Er sieht super aus und man weiß direkt, welcher Schlüssel zum Fiat gehört! Das Modell lässt sich auch ohne AMS oder anderes Mehrfarbsystem drucken! Einfach eine Pause an der…
This model exhaust pipe is compatible with the Fiat 65 toy truck designed by @Patix.
Custom Tweeter cover for JBL stage2 components for Fiat Linea phase1 and Fiat Grande Punto I used ASA for printing. After painting, I assembled it. ABS PETG can also be used. The tabs fit into place; I assembled it without needing to…
This model friction fits right over a 23.5 mm aerator/filter. No glue or threading required. Print conditions: A brim is highly recommended Atheistically, the seam is best when on the back of the part the downloadable 3mf does this (and…
A replacement for the original plastic cover next to the seat of tractors of the Fiatagri 94 series. Originally created for the Fiatagri 88-94. Should fit for at least all tractors of the series. The part is symmetric and fits both sides.…
Designed to replace the rear upper shock bush on Fiat 500/Abarth models but may fit Pandas etc. Designed with the dimensions from Powerflex's bushes due to them being the only ones to produce such a bush. Ensure you use a 30mm or bigger…
Ducato door trim panel clips Fits the large door panels. Print Print sideways with flat side down. This will make it quite strong. Some brim might be good depending on your printer. The FULL version is only for non FDM-printers and is…
TL;DR: Dies ist der offizielle Polarblocks-Remix des genialen BreakTheFiat Cases, speziell optimiert für den Bitaxe Gamma 601 (BM1370 Chip). Drucke dir dieses Gehäuse für dein lautloses Homeoffice-Setup und schütze deine Hardware für…
Side handle for Fiat 600, placed on the seat to raise it. It was printed in ABS with an infill of 20% the use of tree stands with the model placed vertically is recommended If you want to buy me a coffee here is the link ;) :…
Das ist ein Adapter, der zwischen die Rillen bei einem Lieferwagen kommt, um z.B. ein Dachfenster anzubringen.
Fiat Automobiles Keychain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Resize/Scale to adjust dimension If you download/enjoyed this file, please leave a like - Thx All trademarks, logos and brand names are the property of their…
Circle printed flat witch supports, infill 80% but i think 50% should be enough. B printed from composite x on elegoo mars but should be possible print also on FDM printer. Finishing works - sanding, spray putty, sanding again, varnishing…
The Fiat 500e has a key, which is sealed to be waterproof. Downside is, that it is not possible to exchange the battery, at least without destroying the shell. After you manage to get the electronics part out of the shelle and exchange…
Fiat Uno Classic - Keychain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Resize/Scale to adjust dimension If you download, please give me a made and share. It will really helps in my progress - Thx All trademarks, logos and brand…
No supports need Phone cooled on summer, support is on air vent.
Even when I lock the car from the inside, the inner lock of the trunk can open the trunk door. I was afraid my dogs could accidentally open it, so I printed this safety plug to make it impossible to unlock the trunk from the inside…
Key holder to be screwed in a furniture or wall and hold the key of your Fiat Ducato, Peugeot Boxer, Citroen Jumper ... and others. This has been designed for a campervan so we can screw it to a furniture and we have a place where we…
Pretty much what the title says, its a seatbelt buckle/clip/plug to prevent the chime to go non stop, driving me mad This should only be used while going slowly, be responsible and use the seatbelt. i made it bc i live in a place were the…
Replace your broken or missing parcel shelf clips with this precise 3D-printed version. Designed specifically for the Fiat Grande Punto , this clip ensures your rear shelf stays securely in place, functioning just like the original OEM…
FIAT 500 Cabrio This is a model compatible with the LEGO system. Just print it, attach a LEGO chassis, and you're ready to play. Very easy, very simple.
Switch for fiat ducato wind and temperature panel The model has a hole in it that doesnt show up on 3d model
Die Original Version war mir doch etwas zu langweilig. Daher hab ich mir meine eigene Kreation erstellt. Wieder mit eigenen Felgen und getrennten Reifen. Die Reifen müssen in TPU gedruckt werden. Da Sie sonst nicht über die Felgen passen.…
Ich vbrauchte für unseren Opel Rocks E einen Innenspiegel. Diesen habe ich bei Amazon gefunden. Der originale Halter des Spiegels sagte mir nicht so zu, da man ihn hätte Schrauben oder Kleben müssen. Also einen neuen konstruiert. Infill:…
V2 UPDATE: Ok, so i had a brainfart while "CADing" this and made it too tight for no reason at all. Now it should fit MUCH BETTER. The clip has identical dimensions to the original and the same function. The only thing that i could not…
If you want to get this template without subscribing, write me in chat! - SideSilhouette
Recomendo imprimir em ABS ou filamento rígido similar 100% de preenchimento (infill) Caso queira contribuir segue o pix chave aleatória: dbe07593-292e43f8-a5b4-b1c030a573e4 Bruno de Souza Picinini - PicPay If you want, could be nice buy…
There are many key holders for Ducato keys - except for the new version of it. So i went for it and made a fitting key holder. Just velcro or tape it to whereever you like and you are good to go. 15% infill, 0.2mm layer.
My cap's chrome was peeling and the knob was looking bad, this gave it a new life and I no longer want to get rid of my car! This is JUST the cap, to replace an existing cap on the same shifter. My car is a 2012 sport. It fits perfectly…
IT: PER GLI AMANTI E POSSESSORI DELLA FIAT 500L ECCO A VOI IL PORTACHIAVI "MADE IN ITALY" PER VOI! EN: FOR LOVERS AND OWNERS OF THE FIAT 500L HERE IS THE "MADE IN ITALY" KEY RING FOR YOU!
I made this model for a friend of mine who's removed the armrest in a Fiat 500, since it wasn't as comfortable as she's hoped. This model is quite large, the size is due to the hole on the driver's seat leather that has to be there so…
i couldnt find a sink plug for fiat ducato camper van from 2000's so i made one. size of the sink plug is h: 8mm w:31mm for top circle and 28mm for bottom circle. there is also chain clip for standard 2mm ball chain. i uploaded version…
Original document holder must be modified. Use double side tape (or glue) and 4 screw for each side. Print twice (one mirrored) It is for 7 inch 1din radio. Might be used for 2 din (I didn't try it)
This Piggy bank is to celebrate the Western Bitcoin Conference. Put all those fiat coins in and then bury it in the yard!
Flour the cutter before using. First cut the interior and remove windows with a knife, then cut the contour.
Window winder for FIAT Punto 2004 Print instructions Category: Automotive Print Settings Printer: Felix Printer PRO 2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .1 Infill: 20%-100% Filament: PM PETG Black Notes: Bed 85°C,…
Fiat part : 182063280 Compatible with : Fiat Uno, Fiat Fiorino, Fiat Premio, Fiat Elba, Fiat Duna Important : Print horizontally, as per the stl file for better strength.
Konsole für 3 Zusatzinstrumente für den Fiat 126 zur Montag unter dem Radio
Decorative cover for various Ignition Coil Packs. For FPT 4cyl engines (Alfa/Fiat/Jeep/Abarth/Lancia) : BOSCH 0 221 504 713 ( Abarth "legendary BLUE" ) BOSCH 0 221 504 026 ( Alfa Giulietta, 4C - 1750tbi ) BOSCH 0 221 504 707 ( 1.4…
Fiat 1216HP year 1902 Ondersteunt: Ja Resolutie: Dynamisch Invulling: 50% lijn Filament merk: 195 -200 Filament materiaal: PLA
