Counting matching models…
The screw is used to fix the light fixture to the top of the flagpole. A ornament like ball or eagle will not work with the external alpha 915 antenna. If you want to put an internal antenna inside the light fixture, then you can keep the…
I created this flagpole ball (sphere) since mine was damaged last year. I've also included an end cap for the simple look. Additionally the end cap could be combined with an another model (like an eagle) as desired. I'm not sure how…
Replacement bung/plug for a Festivology mast of 35mm internal diameter. I use the mast for ham radio. Intended for printing with TPU. If you wish to use a hard filament, it may be necessary to shrink it in the xy direction slightly.
Remixed Korbyn's RV ladder flagpole mount in Bambu slicer to fit in the corner of a deck and screw into the underside of the 2x6s. Printed with .20mm layer height, 8 walls, and 30% infill with PETG.
As requested by a friend, this is the skull flagpole topper from Halo Infinite! Since the design of the original skull has a section that descends a fair way down the pole, I've cut it off part way as that was what was originally…
This is one part (Solar Panel Bracket to Flagpole Mount) of an assembly. The completed assembly is a meshtastic node atop a 20Ft telescoping flag pole. Related Hardware: RAK Wireless WisBlock Meshtastic Starter Kit:…
This highlights the fact that the Sea Scout Logo isn't symetrical, but I tweaked the inverse to fit the same shape as the front. The screw hole is the edited side, the front is the official logo. Screw needed is an M3 or equivalent. This…
I Made a nice FlagPole Swivel Mount ( ring ) Use only outside support, remove support then press the ring loose I made an extra swivel mount for the top, for a better movement FlagPole Swivel Mount Ø 30 mm inside 47 x 62 x 34 mm FlagPole…
I have a standard flag pole from Lowes/Home Depot. The flag attachment rings work; however, they fail over time. I created these larger, more sturdy versions to replace them (17mm internal diameter). Also, my flag pole came with a clear…
Instructions Print with an outdoor-safe filament, like polycarbonate. Use a coarse gyroid infill and no solid bottom layers. Coat two rods of up to 3mm diameter with epoxy and insert them into the reinforcement channels. I used 3mm…
This is a simplistic adapter which can be used to mount a v2 Starlink Dishy onto a 1.90" diameter Flagpole Buddy Aluminum pole. This is an effective replacement for the official version, in case yours has been lost or possibly just left…
Top and bottom swivels sets for use with 1" diameter flagpoles, with three example caps. Includes Fusion 360 source files (.fd3) and .stl files. The swivel set pieces are printed twice; once for the top of the flagpole to secure the top…
This model is a flag holder for a 6 mm flagpole for a Woom 3 children's bicycle. The holder accommodates a 6 mm flagpole. I printed the part from ABS-GF. PETG was not stable enough for me. This is a flagholder for a 6 mm flagpole. It is…
I Made this design to create a cover for the protection of the flagpolepipe in the ground.
Simple holder for a ball pin (sewing pin) to be used as a flagpole. A thin wire will also work. Flags should be printed on paper on a colour printer. Category: Vehicles
The screw is used to fix the light fixture to the top of the flagpole. A ornament like ball or eagle will not work with the external alpha 915 antenna. If you want to put an internal antenna inside the light fixture, then you can keep the…
Description Material: PLA/PETG Layer Height: 0.20 Infill % : 40 Supports: None Print Orientation: Default as modeled
Telescoping flagpoles require an additional Ring, to set the flag at half mast. Half mast is in honor of those that are well deserving of the tribute. This set includes 4 rings. S-39mm M-49mm L-57mm XL-65mm A retainment pin with cap is…
Made to fit a Thule Omnistor awning post and a 6mm flagpole. I used a 6mm aluminium rod as a flag pole. The example was printed in PLA with a layer height of 0.2mm and upside down without supports
This Mega-Tree light carrier is designed to slip around a 2" flagpole that uses a pulley to lift the carrier to the top. The slip-ring is included in case, like my flagpole, yours reduces in diameter to 1 7/8" halfway up. The carrier is…
This spinning flag mount is designed to prevent your flag tangling around the pole. It's a fairly robust design intended for 25mm or 1" diameter poles - a screw is required to fix the parts in place. I prefer to use zipties to hold the…
General This is a flagpole mount that mounts parallel to the way the flagpole itself sits. Great for columns (like pictured) or areas where you don't necessarily have the perpendicular space to mount a flag pole. Designed to look organic,…
replaces the rings on most flagpoles that break. Print at .6 line width, 4 wall lines, 50% infill
I created this flagpole ball (sphere) since mine was damaged last year. I've also included an end cap for the simple look. Additionally the end cap could be combined with an another model (like an eagle) as desired. I'm not sure how…
This is a replacement flagpole cap for typical Finnish 65mm flag poles. I used 25x25mm N female bulkhead connector to connect 5.5dbi antenna: https://www.aliexpress.com/item/1005008984322302.html Rough schematic for my setup: 12V lead gel…
Replacement bung/plug for a Festivology mast of 35mm internal diameter. I use the mast for ham radio. Intended for printing with TPU. If you wish to use a hard filament, it may be necessary to shrink it in the xy direction slightly.
Thanks to ksanislo for the great model. This version of the adapter is slightly shortened to mount a v2 Starlink Dishy onto a 1.90" diameter Flagpole Buddy with the Flag Rings . Flag Pole Buddy says "It is not recommended to fly a flag…
The model will fit most posts from a flag pole ball (after removing the ball). When printing the 2nd half, mirror the model on the X axis in your slicer software. Glue both sides together and mount to the post. The halo around the maple…
I wanted a holder so I could attach a telescopic flagpole to my Tentbox whilst camping at events.
Flagpole approx. 11.5 cm high and 2.3 cm long without the flag, good for model making gardens. The flag should be 3 cm long and 2 cm high. The flag is homemade; it is a trademark of someone I know. Please speak to me in German.…
Flagpole approx. 11.5 cm high and 2.3 cm long without the flag, good for model making gardens. The flag should be 3 cm long and 2 cm high. The flag is homemade; it is a trademark of someone I know. Please speak to me in German.…
Wanted a cleaner way to use a ziptie to hold on the flag so I modified the ring with a ziptie slot
This flagpole holder is for 8mm pirate-flagpoles that I wanted to attach to the kids climbing frame in the garden. Two designs are available. One for screws with a diameter of 3,5mm and another one for screws with a diameter of 4mm. Print…
Made for a 27.5mm diameter flagpole. Prints without support and uses an M5x12 or 16 BHCS with accompanying M5 nut.
A free spinning ring to attach to your flag and flagpole so it doesn't get tangled in the wind. Uses an M8 thread if you need a longer screw end.
Just print and glue the correct side of the stand to the ‘Kugelkopf’. The stand has a 2mm part to fit into the inlet of the ball head, the rest of the stand is conical. I just didn't want to waste filament for too much support and also…
Because of thieves who stole my flags twice now i decided to make it a little bit more difficult for them.
Base or counterbalance for desklamp, magnifying glass, flagpole or something else you need a base for. I needed a desk lamp for a small corner desk, but most desk lamps were too small, too short or too expensive. Therefore, I purchased a…
Please use petg or abs or asa to print this. It stays outside and pla could become problematic. Use a block of wood and a mallet to drive this into the flagpole. The ribs will shear off and leave a perfect fit.
Modified the Christmas star to mount on top of my flagpole Christmas tree. I hollowed out the spires to contain LED lights and used a hollow dodecahedron as the core. The bottom piece is printed in two halves and contains a 1/2" bolt that…
This desktop flagpole holds a single business card (standard 3.5" x 2" size) at the top of the pole, with additional card storage on the base. Prints well with PLA (only tested with eSUN glossy PLA), tight tolerance in the base/top pole…
This Flagpole mount allows you to fly your colors without leaving the ground! It is designed to use inexpensive 1.25" Schedule 80 PVC pipe as a flagpole and attaches to a standard 1" RV ladder frame. You can pick up the pipe at Lowe's or…
This is an addition for brimstone326s great Dice Tower with Secret Chamber for Dice Storage . I think it adds a nice touch and makes it easier to open and close the secret compartment. Print Settings Resolution: 0.2mm Notes: I had to use…
This model is compatible with the lego system.
Flag pole holder. Highly customizable OpenSCAD script. Use the OpenSCAD customizer to select options with sliders and buttons. Specify pole diameter, support size base size, thickness, mounting type, bolt and screw sizes, and other…
This modifiable design is a swiveling flag mount. Two sets are needed for one flag. Search for "NeverFurl Non-Tangle Flagpole Rings" for usage. Print instructions Category: Outdoor & Garden Summary This modifiable design is a swiveling…
Flagpole knob done in Fusion360 from picture. Size D125 x H145 or resize in slicer Never printed it
Specifically made to fit 1" diameter RV ladder and 2 5/16" diameter flagpole (Harbor Freight flagpole). Flagpole base is obviously for the bottom of the flagpole which clamps and supports the flagpole to prevent sliding. The clamps are…
DE: Einfache Spitze für eine Fahnenstange (z.B. Alu Rundrohr: Durchmesser: 29,5mm, Stärke: 2,4mm aus dem Baumarkt). EN: Simple tip for a flagpole (e.g. aluminum round tube: diameter: 29.5mm, thickness: 2.4mm from the hardware store).
This model consists of components to allow mounting of a 4x6" LED headlight lamp on a 2" galvanized pipe used as a flagpole. Fusion 360 source & STEP files are included. UV & heat resistant material, like ASA is recommended as is…
Designed for the PVC base on the Uncommon Telescoping Flagpole: https://www.uncommonflagpoles.com/flagpoles/the-original-telescoping-flagpole/ Designed to be printed upside-down without needing supports. I recommend printing in PTEG or…
WHAT IS IT? This is a cap for the end of your flagpole. I went to check my flagpole in the spring and discovered that the end cap was gone, and thus, I couldn't attach my flag because the end cap had the hoop to clip The Flag onto! I…
Remixed Korbyn's RV ladder flagpole mount in Bambu slicer to fit in the corner of a deck and screw into the underside of the 2x6s. Printed with .20mm layer height, 8 walls, and 30% infill with PETG.
Used for this bike flag: https://www.amazon.com/gp/product/B0C6XHQXDX
I've recently started DMing without a screen for my playgroups. My DM Screen had a nice wooden channel across the top of it so we could easily track initiative order via cards. Since I'm no longer using my screen, I wanted a visual way to…
This is designed for a specific flag (manufacturer unknown) and is dimensioned to fit as a replacement for the weaker rings provided, which broke in the wind. It could be used for any pole with a diameter less than 1.5", and can be scaled…
This is a two-piece model. Glue the spike into the cylinder using acetone. Settings: Nozzle Size: 0.6mm Layer Height: 0.4mm Material: Polymaker ASA Infill: 100%
Settings: Polymaker ASA 0.6mm CHT nozzle 0.4mm layer height Requires: 1x 3/8" wing nut 2x 3/8" washers 1x 3/8" hex bolt
When I got my Netatmo wind gauge I immediately wanted to mount it. So I just drilled a hole in the standard top cap of my flagpole, put a screw in and put the wind gauge on top of it. This ‘solution’ worked for a while, but it looked…
As requested by a friend, this is the skull flagpole topper from Halo Infinite! Since the design of the original skull has a section that descends a fair way down the pole, I've cut it off part way as that was what was originally…
![Flag and Flagpole for [Dice Tower with Secret Chamber for Dice Storage]](https://media.printables.com/media/prints/457153/images/3756791_12fd0cc0-bb02-466f-b203-9fca777af703/95ca4810f5283ecbb39656d4735eb905_display_large_457153.jpg)
