Counting matching models…
Protective case for the Ricoh GRiiix or GRiii camera. It's designed to print-in-place with a flexible hinge. 4-6mm of cushy TPU surround the camera and provide good protection while keeping a lean profile in your bag. I printed mine out…
I started working with 3D for a litle time, I did not find any Mikrotik rb750gr3 for 10 inch rack, so I made my own.
Hello, this is my simple Rack Mount for Mikrotik RB750 Gr3 HEX. I designed this mount to use 1U space ( little bit less to allow some play) Mount is made very thick and sturdy to allow pluging and unpluging of cables without holding…
Printed using eSUN PLA+ Black
1U 10-inch rack mount for a MikroTik RouterBoard RB750Gr3 (installed without its case) and one Raspberry Pi 4 or 5. Requires M3 nuts and bolts for mounting the MikroTik RouterBoard. Requires M2.5 bolts for mounting the Raspberry Pi.…
Makes holding camera a little easier, short and long versions available. Might fit other cameras. Fairly sturdy in PLA but obviously 3D printed thumb grip isn't going to be as strong as a metal one, use at your own risk. Printing…
New version - better grip, increase polygon quality. The top and bottom are the same height so you can print two of the same and use them like this. Required: 6x2mm magnets
Always seems like theres nowhere to put the antenna wire when installing different electronics. This fixs that issue.
This a Ricoh GR3x camera holder for Honeycomb Storage Wall Print settings: Supports: YES, bed only 0.2mm layer height, PETG 这是一个用于 蜂窝挂钩系统 的理光GR3x相机的挂架 打印设置： 支撑：是，仅在打印版生成 0.2mm层高，PETG
Replacement rollers for lower rack on Hotpoint HDF330PGR3BB dishwasher. I own a Hotpoint HDF330PGR3BB dishwasher. One of the rollers for the lower rack fell off and it looks like it sat on the heating element for quite a while as I found…
I've built a few cyberdecks over the years. Pelican case jobs mostly, the knd that look great on a desk but are a pain to actually use in the wild. Too bulky, awkward power setups, not really something you'd pull out in a coffee shop…
I added 4040 Rail Mounts and a pair of tie loops. Print Settings Printer: Mingda Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: unknowen PLA Category: 3D Printer Accessories
Just an Oc i have. It was about time for him to be figurized. Yes i went all out on the title render. I will do this for many other ocs. His lore is significantly enough different. The swords in his shoulders are called "SoulBounds".…
The top and bottom are the same height so you can print two of the same and use them like this. Required: 6x2mm magnets - 4 pc
Just an Oc i have. It was about time for him to be figurized. Yes i went all out on the title render. I will do this for many other ocs. His lore is significantly enough different. The swords in his shoulders are called "SoulBounds".…
Print in PETG with tree supports. Praise Gr33nguy. (XD)
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
![[GR3ML1N] A Handheld Cyberdeck](https://media.printables.com/media/prints/db82350e-8c52-4842-95c6-bc41a85fe69b/images/12739639_cb3f1688-e134-4ccf-9399-c38840b412a2_da77ddd1-f5e9-4430-a159-14930cf87236/img_9763.jpg)
