145 models
1/16 scale model of an off-road car. The model has real suspension and is assembled just with screws. More advanced models are available at www.3Dsets.com . Want to see lots of cool 3D Sets cars builds? Join our great Facebook group and…
I reworked the "Landy Mini" tire to use it for the Landy/Ranger 1/8. I would like to print the tires by myself, so I scaled the tire from the „Landy Mini by 3D Sets from 1/16 to 1/8. I reworked the tire to print it without support and add…
This is a remix of this bullbar for the Landy Mini from 3D Sets. I have added a winch. This bumper attaches the same way as the original one. Included in the model are support structures which can be broken out after printing. The…
I have created some accessories for the Landy Mini from 3D Sets which can be easily attached with some super glue. The colors you can see in the photos. The mirrors can be easily bent in the right direction after gluing, license plate and…
Trailer addon for Landy Mini by 3D Sets. It is just a little remix of by markberk from Thingiverse. https://www.thingiverse.com/thing:4656335
A trailer for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets Remix of the smaller trailer. For me it was too small and it was too high compared to the car. So I remixed it. Also fixed the…
○120mm extend to switch from a 4WD to a 6WD See instructions (pdf build guide file)
Door step for Landy Mini. Print twice for left and right side. Mount using screw from the Landy model. Best result when printed in two colors.
Print spare wheel just from the Landy Mini set and use it with the hook
Stand for 3Dsets Jeep Rancher 4x4 & Landy 4x4 & Bamboo 10/2/2020 - addes v2 upper part for much more stability 13/2/2020 - added v2 middle and bottom part, can now be screwed together 2/10/2023 - adde middle R-20 part for compatibility…
This is a remix: https://www.thingiverse.com/thing:4394842 Mud guard for the front and back of the 3DSets Landy. Logo land rover
This is an alternative wheel design for the Landy Mini from 3D Sets ! I took the original model of the rim, and swapped the center section for a 5 spoke design. The reception of the axle and the tire are unchanged. If you like check out…
Mud guard and trunk floormat with the Landrover logo that fits for the 3D sets Landrover. Print instructions Printed in TPU or TPE
A bullbar for the Landy mini from 3Dsets.com: https://www.prusaprinters.org/prints/41264-landy-mini-by-3d-sets No supports needed, they are pre-modeled in there in the spirit of the Landy Mini model. Just remove them. Print Settings…
Landy Mini impreso en 3d al 125% con chasis modificado para poder adaptar toda la mecánica de un WPL-C24 y todas las actualizaciones a metal que hay para el, yo compré un c24 en kit, que no traía electrónica salvo servo y motor, todos los…
This is a Front Bumper for a 1:8 scale Warn Winch for the 3DSets Landrover Defender. Included are two versions. One with holes to mount tow hooks, and one without the holes. Mount the parts as shown on the pictures. You need the Original…
Jack for 3D Sets Landy 4x4 RC model 1:10 scale
This is a mod that allows you to use this roof rack: https://www.3dsets.com/product/roof-rack-accessory-for-model-4/ on the much larger Landy 4x4 Wagon. You will need at least a 300x300 print plate to print the rack and side rails but I'm…
Stand for 3dsets.com Landy 4x4 Wagon modified upper part for better vehicle balance and better fit slightly wider stand footprint for improved stability Print instructions 0,3 mm layer height, 3 perimeters, 15 % gyroid infill.
Collection of mud flaps for the front and back of the 3DSets Landy. Overview Logo 4x4 Mountain. LandR. Logo. **** Printed with PLA and 0.25 nozzle, color change at 0.65.
With original springs Landy Mini is very "jumpy". I wanted to keep the original design as much as possible and so I added small “connections" to block springs from moving to much.
This is a scaled version of 3dsets Landy Mini. When scaled the screw holes are slightly bigger than an m3 screw and closer to an m4 screw. This model can be done using super glue as well. At its current model, it is NOT turn key. It will…
Imprimir sin soportes. Pegar con cianocrilato a la carrocería.
This is a scaled version of 3dsets Landy Mini. When scaled the screw holes are slightly bigger than an m3 screw and closer to an m4 screw. This model can be done using super glue as well. At its current model, it is NOT turn key. It will…
3dsets.com Landy 4x4 and Landy 4x4 Wagon modification for LED lights Wheelhouses - modified original mesh, added 24mm holes for lights Rings - to be used instead of default printed lights, push the LED light into it Print instructions…
Took the awesome 1:10 scale version by romcoromcoromco , rescaled it for the Landy Mini and modified to hold a spare wheel. Glue to the body with superglue. Print the jack from…
INFO Scaled down the original model to fit the Landy Mini, more items like air intake and original model for full size 3DSets Land Rover in the link below. Credit to original creator: https://www.thingiverse.com/thing:4270060 PRINT…
This print is a continuation of my design from last year . The actual plow is reusable from one to the other, I just fixed a minor issue where it was accidentally slightly angled up on the right side and added the height adjustable…
!!!!! Please read before building. This is a metal geared axle and transmission conversion for the popular 3Dsets Landy, Rancher and Bamboo. Axle ratios are 3:1 to 4:1 the original 3Dsets axles are only 1.8:1. The axles and transmission…
This is a more realistic and functional towbar and trailer coupling for the Landy Mini by 3Dsets.com and the different trailers. The towbar is a remix of RearBumperForTowbar.stl by Matthijs2101 . Unfortunately, this design requires…
My creation of a roof rack, to mount on a 3Dsets Landy Mini: https://www.prusaprinters.org/prints/41264-landy-mini-by-3dsets Print instructions Category: Toys & Games Summary My creation of a roof rack, to mount on a 3Dsets Landy Mini:…
Imprimir sin soportes. Pegar las partes con cianocrilato y luego pegar al techo
Imprimir sin soportes. Pegar con cianocrilato a la carrocería.
Tyre for Landy 4x4 or truck 100mm OD x 35mm wide I designed this in order to print without supports so it has to be mirrored in order to have the tread direction correct for both sides of the car Enjoy! Print Settings Printer Brand: Prusa…
Collection of different license plates for the landy model from 3DSets. Overview Cal01 - 1 Color change. BadNews - 4 Color changes. BLOB Galactic Empire - 1 Color change (BLOB = Big Lump on Board).
Loved @daver18qc's Hi-lift jack https://www.thingiverse.com/thing:3513415 but needed a way to mount it to my Landy wagon from @3DSets. I made two. One is the "full" mount that replaces one of the hinges on your rear door and holds the…
can be printed without supports in PLA and be connected on the pins with glue
Having built the amazing Landy4x4 hardtop from 3D Sets , it is now time to play with it but also to showcase it, and given that he is a bit on the heavy side, I feared that the tires might get deformed overtime due to the weight, if the…
This is a modified electronics box cover for 3D Sets Landy model 3, that makes it possible to remove the seats in order to access electronics underneath, without disassembling half of the car ;) There are 3 files: box is the main body -…
Landy Mini roof window glass designed and printed with clear/translucent PETG. Fits perfectly in open window on the roof cover. Needs to be super glued or secured in place.
I created a fully functional steering for Landy Mini Thank you 3D Sets for the gorgeus modell, and thank you kokynator for the Stiffer Springs Remix if you want to build this Mod you will need 9x M3x10mm allan bolt 3x M3x8mm allan bolt…
Had an issue with my Landy Wagon where my links were flexing when crawling. Sometimes this caused the axle to shift and move the tires into the wheel well causing issues and binding. This is a tool-less, snap-on, solution. These sliders,…
Needed a Headlight lens and headlight bowl (modified) with a 5mm hole for leds the 3dSets Landy build. Print with the dome facing up and use supports. You need a small CA glue dab to attach it to the inner headlight housing.
GT2 Belt Gearbox for Landy/Rancher/Bamboo 3DSets models. Use it with my Metal transmission, gears and axles mod This gearbox has a ratio of 4:1. Paired with the AR44 33/8T gears, it is the same overall ratio as original 3DSets model. You…
This model is now depreciated, please use the new one . Are you tired of clearing your driveway by hand? Is it too small to justify a snowblower or other full scale device? Well now, it can take you twice as long, using your RC. This…
Spare wheel carrier for 3dsets landy. Printed in Prusament PLA with 0.25 mm nozzle. -- Note on the rear bumper and on the right rear fender, holes must be 1.8 mm. Screws needed: 8x M2x6 2x M2x10
A different bonnet for the Landy Mini, pimp your landy. Print at whatever works best for you.
New light + cover. You print the cover from transparent filament. I used Nebula natural. Spectrum alu silk was used for the light
I modded the lights for the Landy to fit 3 and 5mm LEDs that come in most RC light kits on aliexpress.
Designed and printed a rear gate / spare wheel carrier for the Landy Model 3. Based on "Wheel C" . It probably fits other wheels as well but not tested. I have included some simple templates that can be used for the hole positions for…
Imprimir sin soportes
I recommend to print it with 100% infill
There are not many snorkels for our beloved Landy Mini. I found this great model by atelierhemi , that I adapted to be glued to the body. I tilted the snorkel slightly to tightly fit the body. For printing I suggest to cut it in two, e.g.…
Needed more cooling for longer drives. I actually saw somebody post something similar but using a hacked stock radiator. Figured, there's a better way! Enjoy and Post your makes! The fans I used:…
A trailer for the Landy mini from 3Dsets.com. A remix of a remix. A little smaller than the original long trailer, so it fits on the Prusa Mini.
Simple templates you can print to draw around so you can make the glass.
Modifications to 3DSets Landy Wagon (and other 3DSets models) to go to metal transmission from gearbox to wheel, using Thumper axles Use in combination with Gearbox with 3D Printed pulley and Metal output GT2/Metal pulleys gearbox UPDATE…
Created a Towbar and a trailer for a 3Dsets landy( https://www.prusaprinters.org/prints/41264-landy-mini-by-3dsets ) Towbar is the same as for playmobil car. A playmobil boat fits(clips on) on the trailer. Print instructions Category:…
To make it waterproof. I recommend to add silicone (as example Done Deal) on all adjacent surfaces, and to the wires under the small cap. Use it on your own risk! PS: parts are very stiff to connect. Its important for better waterproof…
Just another doorsep for the landy mini. Not a remix because I modeled it, but I basically copied https://www.printables.com/model/113955-doorstep-for-landy-mini and lowered the bars to make it easier to print. I also made it two part to…
Steering wheel for Landy, just print both front and rear parts and glue with superglue. Attach with the same screw as original steering wheel. Printed with 0.12mm layers, 2 perimeters, and 100% infill. Category: R/C Vehicles
This is work in progress I haven't tried to print it myself and test it yet. This is a lens cover for the 3D Sets Landy that you can print in transparent filament. I am planning to use the following print settings and these are present in…
Modified Africa Trophy front bumper with larger winch mount to fit an RC4WD 1/8 Warn Zeon Winch.
Modified the bottom section of this bullbar made by Matthijs2101 because the it looked very blocky and not very practical offroad. Also added tow hooks because they look cool. Intially wanted to add a winch too but the dimensions didn't…
Rear wheelhouses for the Model 5 Landy 4x4 Wagon that has holes for led lights This has the openings for all the rear lights of the Landy model Print on .20 resolution in black PLA. No supports needed as per original design by 3Dsets
3Dsets Landy 4x4 Wagon ESC switch holder for QuicRun WP 16BL30
Issue at first run: tire pops out of the rim. I create this simple cylinder, in order to put it inside tire and lock it into the wheel when screwing the rim. (It press the tire between internal beadlock and rim). Not miraculous (still…
This is a resized license plate holder to fit EU-size rear license plates for the 3DSets Landy
This is two different trailer covers for the Landy Mini Long Trailer, one flat and one tall.
Sin soportes. Imprimir en PLA translúcido.
I think the Landy Mini didn't have an exhaust and I designed a simple exhaust for it. I painted it with a silver spray. a model for FDM 3D printing, resin or both. exhaust for Landy Mini by 3D Sets.…
This is remix from pruzkumakkoubahadr's design "Landy ARB front bumper", allowing to mount 3dsets winch & servo guard
This is roof rack for Landy Wagon from FedorSosnin, remixed to fit smaller print bed. Biggest part is 175x156
Imprimir sin soportes. Pegar con cianocrilato.
A faux led bar for the ARB style bumper by @pruzkumakkoubahadr. I suggest using -.025 Horizontal expansion on both parts for a snug fit without sanding. Enjoy and post your makes!
New rim for the Landy Mini in the TWIN-MONOTUBE-PROJEKT-AT20 Style Print with high resolution or use my for Bambu X1C optimized 3mf file because I changed a lot of settings. Use ironing for the top layers. I printed the base with 0.20mm…
window frame for Landy Mini by 3D Sets. I designed a window frame for the Landy Mini and also used one-mil plexiglass. I will put the file and you can cut the plexiglass. window frame for Landy Mini by 3D Sets.…
Adapter for use 20V Parkside battery in 3D sets Landy. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0,3 Infill: 30 Filament: Prusament PLA How I Designed This =================== Designed in…
⚙Disclaimer: This is a modification of the original files from 3Dsets. You will need to purchase the original files in order to build this mod in its entirety. Some crucial parts for the differentials are missing! I’ve included only the…
Frontbar with headlights for Landy Mini. Headlight print twice for left and right side. Mount using glue. Best result when headlight printed in transparent filament. Headlight's covers shoul be printed with the grid facing the printer…
for installing RC lights like GRC 17mm headlights instead of original frame - remixed from 3Dsets original bumper frame
Hello! I made a Lowboy tipping trailer for Landy mini. You will need some screws and glue for finish this piece. Feel free to remix it. I was inspired by these models:…
The spare wheel holder for the Landy 4x4 Hardtop vehicle model. Print from PLA with a 0.15mm layer height. Insert the M3 nut and attach the holder to the drilled holes with four M2x6 screws.
Introducing printable and fully working Salt spreader for 3D sets cars Find out more under this link: https://www.printables.com/model/684293-3d-printed-salt-spreader Detailed instructions are available as well as BOM list This part is…
This model is based on previous work of @Gosga365 and @Petr Gaube on which I remixed. Slim Kanto Pokédex that's perfect as a prop for your Pokémon outfit. All the pieces are separate so you can multi color print it if you like it.…
This model is a landyard adapter for the radiomaster pocket IMPORTANT it has only been tested on the radiomaster pocket Soo I had some problems of compatibility and designed this in 5 minutes, printed it one time, liked it and I decided…
Cropped roof for Landy Mini
Eine einfach zu druckende Wandhalterung für Modellautos. Optimal für den Mini Landy. Gedruckt mit PLA+ 30% Infill.
I modified the Board Clips from the African Trophy Set for the Landy to fit on the normal Roof Rack for Model 4. Now you can clip the recovery Board side by side to the normal Roof Rack.
Prints well with Pla And is great for Making your keycard be in a accessible place
To be able to hide the cabling i have made this hidden floor cable deck. This can be printed in .20/.30 PLA with no supports
Print in material of your choice. I used PLA and printed with 100% infill at .3mm layer height.
Licence plate for 3DSETS Landy Model 5 with 6x6 upgrade print with layer height 0,15mm, change filament at 0,35mm
Removable seats modification for the 3dsets model 3 Landy pickup. Allows access to electronics without requiring disassembly of the interior. I remixed an original model to remove the reliance on a metal spring, which I was unable to…
The tray for 2S LiPo battery pack under back seats of Landy 4x4 Hardtop vehicle model from 3Dsets. It counts with the wires on the right side, if necessary simply mirror it in PrusaSlicer. Print from PLA with a 0.2 mm layer height and…
Drill two holes in the back of your board and attach. It is really that simple 80% infill for the plate and screws gyroid infill pattern no supports
I wanted to have off-road rear bumper on my Landy Wagon but I also wanted to tow the trailer. So here is the result I mixed original hitch and original rear bumper. Original hitch is slightly higher to by aligned with the tubes on the…
Originally a rugged tool box from @Yanev (https://www.printables.com/model/39729-tool-box-parametric) altered in size and shape to snap-fit on the 3dsets model 4 (maybe model 5 as well) with the africa trophy roofrack. I plan to drive…
