219 models
Use PA (nylon), PC or some other temperature-resistant filament. Do not use PLA, or carbon-infused filament, as it is likely to heat up because of its conductivity. Printed at 0.20m QUALITY settings with 40% infill.
Replacement interlock button for KitchenAid button KCMC1575BSS1 with sturdier construction.
My daughter kept saying her dollhouse was missing a microwave and a 3D Printer. Well, here is her microwave complete with buttons. Door does not open. I got lazy and she said she didn't mind if the door is fixed. As a result the inside is…
I couldn't find a microwave popcorn box that would use a FIFO storage method and be able to see how many bags were left in it. This will hold 9 bags of popcorn. 20% infill Some supports are needed. Printed with Numaker PLA+
The door button on my LG microwave stopped working, because it is designed to connect to some very weak plastic tabs that act as a hinge. In my case, the plastic tabs broke off, and the button no longer worked reliably. I designed this…
The wheel off my microwave roller wheel broke off, create a new one and improved with more wheels so it is more stable. Diameter of 19.5cm. Originally design for Sharp R-210D(W) Simple to print, I used CPE to print at 0.3 layer height.…
Door latch for microwave oven BEKO MGB 25333 BG. The original door latch tab broke and microwave stopped working. The service center offered only a complete door as a replacement, for which they asked €90, which I kindly refused. 3D…
Microwave door handle has been broken forever. Finally broke the rest of the way . So, modeled and printed a replacement. This one is significantly more stout than the original, so maybe it will endure my kids abuse. Printed in PLA, on…
A classic use-case of 3D printing… a flimsy replacement injection-molded ABS part costs a fortune to source and is discontinued by the manufacturer. This is the part that links the glass plate in a microwave oven to the driving motor…
This knob is a replacement part for the Whirlpool MD111 Microwave. It has two parts that you should glue together with superglue when you set up the correct angle for the 0 position. Print instructions Category: Replacement Parts Print…
I wanted to place my microwave on a wire shelf rack. The feet did not align with the rack, so 3D printing to the rescue! I figured I would share the model since I'm sure it could be useful for other appliances. Microwave is a Panasonic,…
Replacement piece for the turning plate of the Combi C105 microwave oven. Print instructions Category: Kitchen & Dining Summary Replacement piece for the turning plate of the Combi C105 microwave oven. It might fit yours, the outer shaft…
Here is a replacement part for any microwave that has a standard Ø 180 mm 5889W1A012A turntable. It's commonly used in budget devices. All you'll need is a T10-T20 torx screwdriver for the assembly. Tip : print the sample test first to…
A printable door release lever for Panasonic microwaves matching PN 5Y00AP / F82565Y00AP. Slightly modified with more internal vertical supports to make the part a bit stronger and print friendly. Print with the 45 degree surface aligned…
YAGNI (You ain't gonna need it) But if you are really the one person on the world who also needs a replacement for the turntable of a 30 year old Miele M8160-2 microwave oven , send send me some kudos, please. Took the model from Zendama…
Update: Added a cut-up version of the inner dome for easier removal (for 5mm wall thickness). Use this 3d-printed mold to make crucibles from silicon carbide powder and waterglass for metal melting in the microwave. It holds about 110ml.…
Microwave knob I created for my microwave. Printed in BambuLab X1C from PLA, 0.2mm layer, no supports needed I added some tolerance for the shaft, add a comment if you want it modified Please upload a make if you print it, I'll appreciate…
Lily with microwave miniature. Print with support. Other models: https://makerworld.com/@Misakov/collections/5259590-sprunki If you like the print, don't forget to like it.
Microwave Motor 1:1 - Accurate 3D Model for Projects and Reference This 3D model represents a microwave motor at a precise 1:1 scale, ideal for engineers, designers, and 3D printing enthusiasts who want to use it in their projects or…
This control knob was designed as a replacement for my mother's microwave. The original had a spring steel ring at the end, which i wanted to reuse to add some stability and strength, that's why the middle cylinder is narrower at the top.…
Microwave Cover for Food / Anti-Splatter / Finger grips. Both are 65mm tall. The 210mm dia is the largest it can fit on MK3S. Material: Transparent Polypropylene (PP) or PETG
Supports: Yes Time: Depends on Scale Printer: I use an Ender 3 V2 Neo
The handle broke on our over-the-range GE microwave, so I slapped this together in Tinkercad to print a replacement. It has some issues, such as the mounting pegs are not evenly spaced on the handle ends, due to my assembly in tinkercad…
The handle on my 20ish year old microwave was cracked and falling apart and I couldn't stomach paying $70 OEM. My partner started asking questions about buying a new microwave so I knew I had to jump into action. I was going to model the…
Tiny but useful! So, no lie, my microwave roller broke, and I got out the calipers and printed a replacement. I was worried that the PLA would melt in the microwave but it didn't. Not even after months. Fits my mircowave, rolls great.…
it was one of those typical situations where I thought "if I had a 3D printer - I do!" The rotary axe of the microwave had become hot for some unknown reason, melted and the whole microwave was suddenly no longer usable. But it's a small…
This is a replacement handle for a Kenmore microwave. The part number is 3650W1A075H but it's been discontinued. I've included the .stl file for the handle and also a base to which the handle can be attached for sanding painting. The base…
A colleague broke one of the knobs on his microwave, designed this one as a replacement in Onshape. Can be printed with AMS it you want to have a black arrow at the top, however should be easy to color using a sharpie. Designed for the…
Replacement wheel / roller for Samsung microwave oven. Because of the worn wheel, my turntable made strange noises.
The dimension are correct, printing from petg plastic
One of the buttons of my microwave broke off and instead of buying one I used it as an exercise in reverse engineering. I decided to print it in 2 parts too avoid supports since there isn't much space to remove the supports and the…
Button designed to replace a broken door button for a Panasonic microwave. 2018-10-25 Update: Added some curves to strengthen the design. Category: Kitchen & Dining
A friend's microwave door latch broke and asked for a replacement. Cooked this up in Fusion 360 only to realise there were similar models available online that could have worked. Nevertheless this was a fun project. Hope my version works…
Small press to dry flowers in the microwave. The press is 65mm x 65 mm and printed from PLA. Bottom has a recess for a piece of corrugated cardboard as a cushion, flowers can be dried between 2 pieces of paper towel to absorb moisture.…
I printed the model with PC (polycarbonate) - high temperature filament suitable for microwave. No printing support required. Settings are shown on a pick attached. Who colors are for aesthetic purpose and the second one is not…
This part is pressed to open the microwave door. the microwave door is locked and does not have a handle, To open the door you press this part and the microwave door opens. This part is for a Samsung microwave.
Replacement of Siemens microwave oven knobs (originals (Pekalit) broke out at shaft). Small nose for scale printed as separte part to enable easy usage of different material a have an nice, sharp contrast. I used PETG (black) for the main…
Door latch for microwave oven Thomson Microwave Oven COMBIMAT 25. But I would not be surprised if it fits other models and brands as well since they all look alike. These door latches break off easily. Mine did as well and after numerous…
Manopola microonde - Microwave knob Manopola timer per microonde - attacco universale
I made a few changes to the hook to hold onto the cover a bit stronger. I also made it wider so that it could be mounted with a command hook strip instead of a screw.
These are some simple feet risers to rise your Candy EGO-G25DCS microwave oven. Print instructions Material PLA Resolution 150 Supports No Brim No
What is it good for? I use this bowl to refresh my silica gel in the microwave. Put some kitchen paper in the bowl to avoid melting the plastic when the silica gel gets hot. Put it in the microwave at lowest power for a minute. Get it out…
Replacement plate rollers for Sharp microwave Old rollers had worn so badly that plate did not turn smoothly and made a lot of noise These rollers snap onto the existing frame Print instructions No special instructions. I used PETG.…
I needed a replacement handle for our Kenmore microwave, model #40185049210 and did not want to pay over $60 for one including shipping. So, I took some measurements of the old one, and had one ready the next morning ready to put on! I…
HO Scale Spacers used to build Comunications Tower with Cell and microwave Antenna Using florest wire the spacers make a HO Scale tower. Cell and microwave antennas included My source of Model train things is WWW.RailGoose.com Print…
This part is a replacement for a part in my microwave door. This part is fixed in the door and latches to the microwave which allows the door to open and close.
Spojovací váleček otočného talíře v mikrovlné troubě. Tento je pro značku Baumatic, ale bude fungovat i jinde. Na fotkách je kousek po několika měsících používání. Je to PLA, ale v podstatě to teplotně stačí. Když tak se po čase vytiskne…
A dispenser for storing microwave rice packets easily and being able to use them without having to unpack the storage area.
WIP - the handle is maybe 0.2mm too long over it's entire length, and there's not enough margin on the “boltway” parts: I cracked my handle slightly while putting them in. But it fit on line, so I probably will not fix this model, unless…
Is printed in two parts which need to be super glued together. No brim or support needed. Printed in PLA.
3D model of MLEVPB016MRF1. It will Requires supports, but I have designed it for printing as much as possible. Fits many Sharp carousel microwave models. Here is a list of what microwaves it fits: • R1210 • R1405 • R1406 • R1461A • R1462A…
This is my answer to the high cost of appliance repair. These handles have holes set at 189mm. I have included the step files if you need to modify either of these models. Printing For style 1, you may want to print it on it's side with…
Ikea microwave plate drive replacement part
Hello, This box was created to adapt an old microwave fan to a wall mount. The structure for mounting the fan was taken directly from the microwave. The model number of the fan used here is: SMF-745EA1 Category: 3D Printing
This control knob was designed as a replacement for my mother's microwave. This version doesn't have the narrower part of the middle cylinder, which was meant for a spring steel ring. Print Settings Printer Brand: Creality Printer: Ender…
Quick and dirty mount for a plastic microwave plate cover Print instructions No specific considerations other than maybe using PETG, the cover can get pretty hot
Fits microwave model NN-SN661S and possibly others. Panasonic part # F82569Y00AP Printed just fine without supports on my printer, but your mileage may vary (see orientation in photo). (Probably would have “looked” nicer in a different…
It is just a simple replacement for my broken Microwave Knob
Originally published here: Cosmic Microwave Background Radiation scaled one in 2*10^28 by tato_713 - Thingiverse This model was made using the data of the Plank spacecraft of the Cosmic Microwave Background (CMB or CMBR), processed with…
This knob is a replacement part for the Whirlpool MD517 Microwave. It is single-part printed with tree support with the handle down. Printed with standard nozzle (0.4mm) and PLA. Really solid part with the perfect fit. No postprocessing…
Anyone who has ever had a GE microwave has probably had the handle brackets break. The OEM bracket is very brittle and gives out before too long. Print your own replacement. They print best with minimal supports placed stem down at an…
A simple hook to hang your microwave plate cover.
Coupling for microwave oven TEKA ML820BIS. The coupling on my microwave oven broke (it split where the motor
tisk výplň 100% tryska 0,4 kolečko tryska 0,25 print fill 100% nozzle 0.4 wheel nozzle 0.25
Low Poly Microwave Oven 3D Model
Created this to place my microwave cover be placed under my cabinets. You want to print with support.
You should print this with as many walls and as much infill as you can tolerate, and tune your printer to print as much detail as it can achieve with the least posible distortion you can manage.
It is frustrating when you want to turn on the night light on the microwave, but cannot see the button. And all buttons are smooth, so you can't feel where it is. I created this light bulb icon to print and place on the lightbulb icon on…
This is a replacement handle for a GE Spacemaker XL under-cabinet microwave. The handle on mine broke and replacements are impossible to find so I designed my own. Print this with the front face down. No supports are required. I printed…
Oddly my Kenmore Microwave didnt come with feet so I made them. Settings Layer height: .2 Supports: yes Filament: PLA+
mtmustski your Thing was a life save!!!!! Our door latch 'mysteriously' broke - all by itself it seems...... Wish i had seen the broken latch before I took the Microwave completely to bits and checked EVERYTHING else :o( Anyways, with a…
Not much to say really, use whichever print settings you'd normally use for everyday prints. Microwave steam lids are not heavy so I went with 10%. You could adapt this for other things so scale as needed. Fusion files included if you…
I've included the STEP file in case you want to modify it for your microwave. I printed in PLA with relatively high infill (50% or so). I expect it won't last as long as the original, but it'll be a lot less than $150 when I need a new…
Accidentally snapped of a latch tab on my Miele microwave oven, replicated the part in Fusion 360 and printed in Prusament PETG. I believe it is part #6635824. Looks like it is used by a lot of different manufacturers and models also.…
Quick design to replace a busted plastic microwave handle. Uses a 1" hardware store dowel as the main handle. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Yes Supports: Yes Resolution: .2 Infill: 100 Filament: Hatchbox…
I wonder if anyone ever needs this but as I was proud to create my first own CAD model I though it's worth sharing. Due to exessive force (wifey smashed the door against the microwave's) the door mechanism of my Sharp microwave broke. I…
A large turntable for filament spools. The print files here (STL) have the outer diameter of 176 mm so that they fit reliably on my PRUSA MINI+. However the SCAD source makes it fully configurable. All dimensions are set at the beginning…
Allows you to store your microwave cover anywhere you desire. Designed for Nordic Ware splatter cover. May fit other manufacturers. Assemble with #6 screws (~3.5mm). I added felt stickers to increase the friction. Material: Any
I bought a replacement plate for my GE 731K microwave and it turned out that the protrusions under the plate were higher than in the original. So I had to improvise. The plate that I bought is DE74-00027A and was supposed to be a direct…
-- EN version -- Microwave foot bracket to be screwed onto the furniture. Allows keeping the microwave in place during door opening/closing. Printing instructions: Use a heat-resistant material such as PETG and print with 100% infill to…
The old microwave turn table stopped turning. Upon investigation, the ceramic drive cog that fits between the clockwork motor and the turn table had split on the motor shaft. A few minutes with my calipers and 3D builder, I sliced up and…
It's just a press-in Foot clip for an old Quality-Beige HomeStyles Microwave from Hudson Bay. Model: EM820CKH-P00K Created the clip as a learning exercise for FreeCAD and uploading to printables Would be shocked if anyone else actually…
Model was printed with silver PETG on a Prusa MK3S with bed only supports at 0.20mm Quality.
Door latch for microwave De Sina WD1000DI 930C
The main handle on this microwave is made of steel, but it mounts via 2 plastic pieces (painted to look like steel). The plastic parts are fairly easy to break, and the handle is only sold as a complete unit, as far as I could find. Print…
a part for the door release mechanism broke on a Severin microwave. Modeled a new one to replace it. Optimized the broken part with a support piece.
If you flip the model on its back it doesn't need support material.
piece that makes the microwave plate turn
A replacement plate for our microwave. It has a groove and detent on the bottom to fit the rotating part and wheels and is split into 2 parts that friction fit together. It includes my logo and the logo of our hackerspace. Let me know if…
I modeled a functionally equivalent replacement for a broken handle mount. I printed in Polymaker Galaxy Black ASA. 0.2mm layer height with variable layer height activated for top surface profile for the best possible contour. I reused…
Replacement handle for an Emerson microwave. Designed to use the existing screws.
This part broke on my microwave and a replacement is about ~$60 here in Canada (slightly cheaper if if I order it from the US). I decided I would print my own, and hopefully others can use this as well. My microwave is a KCMS1555RSS but…
