39 models
The original ModMic base clasp is under constant stress and can breakdown quite quickly. Here is a replacement part. It is almost like the original, but with minor tweaks for 3D-printing. I use this for my ModMic Wireless, and it works…
Upgrade your Antlion ModMic Wireless with this oversize battery cover that supports up to a 600mAh LIPO 503040 battery. This is a simple and easy way to extend the battery life of your ModMic Wireless by up to 200%. Spacer is to fille the…
Add a 6x2 mm magnet and some 3M adhesive and you can use your microphone on another headset. It might bee necessary to use glue to get the magnet to stay. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No…
Don't know where to put your ModMic when you're not using it? This is the print for you! This small holster allows you to hang up your ModMic Wireless anywhere you like. It's intended to be used with another fastener - e.g. velcro, 3M VHB…
A place to mount an Antlion ModMic wireless microphone that can rest on your shoulders. Allows you to use the ModMic if you use earbuds, incompatible headphones, or no headphones at all.
This requires a 6x3mm neodymium magnet (what I had lying around). I have included the step file if you have different magnets on hand.
my plastic holders that came with the mod mic all broke but the magnets worked fine so why not make a version that allows the use of the original magnets. the microphone holds even stronger now than with a original plastic bit. i hope…
Print with the smallest Layer Height you can and 100% Infill. Each part should work with the original Counterpart. You have to glue the magnet in and maybe soften the plastic a bit by heating it up. If you need a base try this one:…
Adapter to fit the ModMic Microphone to the Sony XM5 using the 3.5mm jack on the headphone. Prints well at 0.15mm height without any support (other that the support build into the model.) Use the magnet from the standard ModMic adapter…
The genuine modmic cable clips are far to expensive for this little plastic in my opinion. So i designed them for 3d printing. Works quite well for me. Single wall print, add brim to hold it to the print bed.
Needed something to store and charge my wireless modmic. Didn't find anything online so I can up with this. So far its working great. Setup to use small screws for mounting. Double sided tape may also work but I have not tried it. Used…
A generic version of my modmic mount for relatively flat headphone cups. To use it remove the double sided adhesive that came already attached the modmic mount and replace it with a big sheet of 3M VHB or similar
A small mounting surface to mount your modmic to your pair of Sundaras. Bonuses Allows avoiding mounting directly to the headphone cups. Allows the mic to swivel slightly left and right. Hardware 2 x M3 16mm flathead screws (I used…
The small adapter has a fin that screws in behind the cable guide. Original screws can be used. The modmic adapter clip seats in the recess.
I have no clue if it is possible to print this on variety of printers as it is quite a tight fit (0.05mm on the entrance, scaling just a bit should fix it though). Could not come up with better solution for the rotating mechanism, lol.…
Was getting frustrated with the modmic losing adhesion from the k7xx headphones as there was no perfect spot for it. Designed this to allow for a solid surface for the modmic to attach to. I printed mine with the pad side down. Category:…
This is a remix of lionpants' original modmic mount, but adjusted for M3 10mm cap head screws Changes to Outer 4mm counterbore for M3 10mm cap head screw Changes to Inner 4mm captured nut (extended from 2.4mm) for M3 nylock nut as opposed…
Add some 3M VHB double sided adhesive or other similar product to the back and stick it onto your DT880s
Press-fit a 6x3mm magnet at the holder and you're good to go.
The spring clamp for head(amame) V2 with an added flat circular spot sized specifically for mounting a ModMic.
To edit the OpenSCAD File you'll need https://github.com/revarbat/BOSL2
Remixed @CookieTyrant s excellent work to add some rolled edges as well as open the internals to better accommodate my particular battery I used on my mod mic. NOTE: grab the spacer from the original file set:…
I was never a fan of the microphone on my A50 headset, but I like everything else about it. It's been my daily headset for 6 years now. Recently the microphone started behaving really weird, clipping my voice out unless I was in a silent…
The model uses a 8x3mm Magnet for the mic mount, 10mm m3 screw, m3 hex nut and a 2.5 to 3.5mm jack. Jack - https://www.aliexpress.com/item/1005006194351413.html?spm=a2g0o.order_list.order_list_main.12.7bb91802MsqEWi
I use bone conduction headphones to game as I have a toddler, and also due to the toddler the desk mic isn't a great solution. I found the ModMic, but as expected the magnetic mount doesn't stick to the rubber on the Shokz headset. After…
Custom design to allow a ModMic to sit perfectly on my Open Alpha headphones (Alpha Dog open source design), the plastic on the Fostex T50 is too smooth to allow a good bond with the original mounting hardware. Snaps on and off securely…
I really like that you can see if the mic is connected and muted or not on the USB receiver, but the blinking when not connected is very annoying. This simple sleeve can be pushed over to cover it and pulled up to view it again.…
Made this because the glue kept wearing out. I printed it with columns. To attach, put the clasp that came with the ModMic into the circular indent and snap the whole thing onto the headphones. Like this:
A topology-optimized (for looks, probably not necessary) adapter to install an Antlion Audio ModMic Microphone properly. Made with high density and a lot of thickness, because otherwise it could be brittle.
A way to use your Mod Mic with iems and in style. I purchased a $1 hair headband that had fabric over it. I cut the fabric off. The fit of the print is very loose to allow for adjustment. Once you find the position you like, mark it and…
Attachment for my old ModMic on my Stax Lambda. It works with almost any aftermarket ModMic clone. I did not want to have a magnet next to the Stax drivers, as they are sensitive enough. I suspect this may have caused long term damage to…
I crudely added a HSW fitting onto this holder in tinkercad so it can go on my wall. Printed with esun transparent PETG on K1 0.24, Tree supports on build plate only for the fitting
Nuraphone ModMic Wireless Mount. Friction fit and the 2 pieces glued together with a VERY small amount of supe glue.
This is a simple design that turns a magnetic breakaway cable into a dock for charging small devices. In my case I'm using it for a modmic wireless under my desk, but there's no reason why it couldn't be used for something else. The cable…
i remixed the original to have a wall around the magnet thing. also i changed the hole to fit m3 4mm FCHS screws which screw directly into the plastic. if you want to avoid that it will probably also work with hotglue
Small Adapter for Beyerdynamic with mini XLR Plug and AntLion-ModMic
I really like that you can see if the mic is connected and muted or not on the USB receiver, but the blinking when not connected is very annoying. This simple sleeve can be pushed over to cover it and pulled up to view it again.…
I use bone conduction headphones to game as I have a toddler, and also due to the toddler the desk mic isn't a great solution. I found the ModMic, but as expected the magnetic mount doesn't stick to the rubber on the Shokz headset. After…
i remixed the original to have a wall around the magnet thing. also i changed the hole to fit m3 4mm FCHS screws which screw directly into the plastic. if you want to avoid that it will probably also work with hotglue
