Counting matching models…
I really like CSD_Salzburg's Skadis designs but these containers just take too long to print. So I adapted a vase printing idea to be used with the IKEA Skadis containers and added a little twist. I also added a little feature trick to…
Radio Box for Mayako MX8E E-Buggy – includes integrated transponder mount designed for MYLaps transponders. Designed for a clean, secure install of your electronics while keeping your transponder neatly positioned and protected. Perfect…
When the gearbox is reassembled rotate the drive wheel in reverse until it's in the neutral position on both sides before installing. So that they synchronize and it doesn't just go in circles.
0,2 layer height 5 wall 4 bottom 4top layers
I bought the HEPA filter linked in the original BentoBox filter comment section from Amazon. about 42mm x 83mm. Remixed the filter container to fit it exactly. also reduced over all height. works with the original cover. I have not…
My Zodiac MX6 pool cleaner swivel assembly broke and the only thing available I can find on amazon is this complete set ( https://amzn.to/446w9Kp ). Luckily, I found the particular part I'm looking for made by BrianM2. I remixed his…
Repair parts or Zodiac Baracuda MX6 MX8. The pins are the first thing to break, you need to print them slow, hot and with hard material, and horizontal. They typically dont last that long.
When your Zodiac Baracuda MX6 or MX8 hoze lid attachment wears out you cannot remove it without breaking it and probably losing all the small balls for the bearing inside. To fix it you need to buy a complete new lid with bearing and…
Lets you use a standard pool vacuum hose. I got a 35 foot hose from Lowe's or Home Depot and cut it to length. Way cheaper and lasts years longer. You need; 2X the half circle pieces 1x the full circle (hose) piece 2x M4x10mm STAINLESS…
This thumb screw allows you to insert an M4 nut into the printed part and which will allow you to tighten and loosen the battery hand rather than using a tool.
https://github.com/ntchris/voron_mod_super_diy/tree/main/ercf_v2/filament_tension_sensor_hall Inspired by Annex-Engineering's Belay sensor module https://github.com/Annex-Engineering/Belay Inspired by jmillerfo 's Voron ERCF Filament…
Kolečko pro uchycení pásů posuvu podvodního vysavače průměr: 70 mm Dvojitý T profil
Porta carnet de 5,5cmx8,5cm = 85x54mm = 2"¼ x 3" ¾
Thumb Screw for M3 Bolt and Nut to Lock Out Steering on a Mayako MX8 RC Buggy This custom-designed thumb screw is an ideal accessory for RC enthusiasts looking to fine-tune their Mayako MX8 buggy's steering setup. It is specifically…
Got tired of getting sawdust on my stones. Designed to fit a set of diamond stones that are 8x3x0.3", or 205x80x8mm. I also have a strop the same size that I glued onto a piece of 3/8" ply, so the top slot is slightly taller (14mm). It…
So for this Cover, I have tested is the Malaysia 3x6 One, The UK one is untested. And the 2x Hole is for super short Metel Buttom, something like this: Note You need a 22mm Metal Button.
Home vent 3 inch. No animals if you drop it below the plate in the slicer . 😁🐊🐧
Louvre air vent used - https://www.screwfix.com/p/map-vent-gas-louvre-vent-white-229mm-x-76mm/4548d Fans used - https://www.amazon.co.uk/dp/B0C8CPZJ11 Printed in PLA with 0.6mm nozzle at 0.3mm layers, but any settings or material should…
https://github.com/ntchris/voron_mod_super_diy/tree/main/ercf_v2/filament_tension_sensor_hall Inspired by Annex-Engineering's Belay sensor module https://github.com/Annex-Engineering/Belay Inspired by jmillerfo 's Voron ERCF Filament…
If the hoses are permanently bent, they retain their curvature. I always hang 2 meters vertically with this suspension device.If the hoses are permanently bent, they retain their curvature. I wanted to hang 2 meters vertically straight.
I didn't have PVC laying around, so I quickly modeled a dowel rod to use. For some reason the STL loads really small in the slicer, so make sure that the dimensions are 19mm diameter (x and y) and 85mm tall/long (z). I printed in PETG…
Louvre air vent used - https://www.screwfix.com/p/map-vent-gas-louvre-vent-white-229mm-x-76mm/4548d Fans used - https://www.amazon.co.uk/dp/B0C8CPZJ11 Printed in PLA with 0.6mm nozzle at 0.3mm layers, but any settings or material should…
