Counting matching models…
THIS IS A REUPLOAD! I did not 3D model this file, it was designed by LayerOne3D over on Thangs. Original model description below: Small desk organizer inspired by shopping baskets! Designed to be support free for 3D printing. Print as one…
The STLs have been sent to Cura and then exported. I exported them as STL binaries, but also as 3MF files, use whichever you wish. The 3MF for the Chain Base Mount includes my setting overrides, which just turns off buildplate adhesion…
Mount for FPV BLITZ M10 AOS CINE35, O3 antenna and antenna transmitters
The only change to this model compared to the original is the lower part of the box. You can use/print the cap, upper half, and tray from the original design.
This half height duct for the AOS Cine35 is based on Chris Rosser's Cine35 Bumper, this version includes an additional bumper added to the outside perimeter. In order to keep the weight down and the bumper flexible (but not too flexible)…
Ein Schutzrahmen für das FairPhone 3 / FairPhone 3+ der so konstruiert wurde, dass man ihn ohne Stützen FDM-Drucken kann. Der Druck funktioniert auch gut mit flexiblen Materialien. Die Löcher für die Tasten können nach dem Druck einfach…
TL;DR - Go straight to the printing and building sections! I normally print with Elegoo's excellent PLA+ filament as I've found it to be highly reliable and prints beautifully cleanly. But then I wanted to use a clear PLA filament, and…
I printed the case made by Tig3rch3n, but I thought there was room for improvement, so I re-made it. It is also snap fit, and the holes should be a little more aligned. You can print it with an infill pattern (and no top and bottom layer)…
Print in TPU with 10-30% infill. Carefully cut through the inside of each standoff hole with cutters if you want to be able to snap the ducts on and off or leave complete for a more permanent fitting.
A case for the Chocorne36-N!N at https://github.com/davidphilipbarr/Choc-Spaced-Corne
Wire grommet that fits in the XT60 hard mount on AOS EVO frames. Have it installed on the Cine35 in the photo. Intended for 14awg wire To install, cut from one edge to center and wrap around the wire, then press into frame. Fits very…
It's a basic antenna mount for TBS Style SMA antennas. Some people feel that these types of Antenna mounts may contribute to frame vibrations, I had to weigh vibration against clarity of video. I could not detect any unusual behaviour in…
Neptune3 shelf with detachable base using a cleat
Elegoo Neptune 3 doesn't support M300 and I needed to know when to tap on Print again because I was printing multiple copies of the same model. So I connected an Arduino and an HC-SR04 ultrasonic sensor to a buzzer (also tried with an…
It all started with the Faiphone3+, then I needed to keep my Nokia6.1 alive 'cause the OLG lottery app wouldn't work on the Fairphone, then my kid wanted one for the Pixel3a. The stands will work with some phone sleeves. Although they are…
Simple and very lightweight case for the Skyline32 Flightcrontroller from EMAX. You can use M3 Screws Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest dieses Teil haben? Schreib einfach:…
Per imprimir directament. No fa falta suports per imprimir-ho. També hi ha espai per guardar les esponges de recanvi.
model of the EMAX Skyline32 Category: R/C Vehicles
I've created this "push on" display cover for the Nordelettronica NE333 because the green LED lights are way to bright during the night. You just need to print the two pieces, put everything together and push the cover over the existing…
Here is the all new Gtech gPhone Series 3 Ultra (or gPhone3 Ultra for short). one of Gtechs first phone models that is actually good. what are you waiting for…? print it!!1111 the color in the picture is titanium white. the side part…
COMMERCIAL LICENSE ACCESS is available through a patreon membership where you help support me and get commercial license which applies to all my models except remixes i made from others work. https://www.patreon.com/Dengamleninja
