Counting matching models…
Just bought the new Norden 901 and discovered, that I do not like the “design” (I would also not call it design) of the OEM phone mount. Gladly I already had experience with phone holders for motorbikes (including 3 broken camera modules…
WWII Norden Bombsight for 1:16 scale RC B-17 I cut away the floor panel and adjusted the scale, as well as cleaned up the mesh for printing. Resin print pictured was done on Elegoo Mars at 100% scale. FDM print was done on MK3S at .07mm…
There was a little gap between the mounting point and the Original GPS Mount (KTM Part Nr. 63512992144); this allowed the mount to rock back and forth, which slowly but steadily seemed to loosen the two bolts holding the mount. The part…
Modular Mount. Baseplate to be added to a GPS Mount/Stant for an Garmin Zumo. Can be changed to a differnet GPS by doing a new GPS Stand. V2 of Garminhold is 1 cm lower above the TFT so it didnt block the airflow.
This is a spare IKEA 108903 - STUVA NORDEN HEMNES - Quermutter - Barrel Nut for an Hemnes bed. We lost one. So I designed, printed and used it succesfully. Just cut or press the M6 thread into it. Use the original bolt for pressing or an…
I reproduced the original Husqvarna ABS sensor cable clip because this cable rubs on the wheel and cuts. It is 10mm longer than the original
These are wheel caster mounts that allow you to install casters onto an IKEA Norden table securely without drilling. There are two sizes – you'll need four pieces of the square-ish one for the main legs and two pieces of the rectangular…
This is a custom-designed lightweight Gridfinity baseplate optimized for the IKEA NORDEN table drawer. The set includes two baseplates per drawer, each featuring a 3x4 Gridfinity layout. These baseplates were built using the Autodesk…
Wanted to make a leg riser for Ikea Norden table, since my robot vacuum got stuck in the table extension all the time. I din't find any existing ones that looked nice enough so designed some my self. Ended up making this aesthetic and…
Our IKEA Norden table (which is a fabulous table) lost one of the insets that are used for locking it in its extended position. I measured the hole and did a simple version in OpenScad. It fit quite snugly at my second try, so even though…
Battery Box for Norden 901 to house a LiFePO Pack with Balancer, 150x87x105mm, plus left hand, m3, petg
Set of Ikea Norden 15mm feets with screw holes. To elevate the Table a little bit. Necessary in my case for my vacuum robot.
I had a problem with our robot vacuum cleaner and our norden table. Sometimes the cleaner was stuck under the Table. I created some simple feed to raise the table by 2cm. I printed the feet with extrudr hard tpu.
This remixed filament spool holder includes two individual pieces and can hold a spool facing the left or right side. It mounts to the edge of the table like the Ikea Norden which measures 24mm in height at the edge. The parts slides into…
Having placed on the front porch an Ikea Norden, that should be kept inside, I decided to design some feet to prevent the table legs from coming into contact with moisture from the floor. I prepared two different types of feet: a square…
Why? The IKEA NORDEN table is a beautiful piece of furniture, but at 47kg it's a beast to move. I use mine almost daily and kept struggling to reposition it; so I designed a simple, non-destructive solution that clips onto the existing…
This is a remix of https://www.printables.com/model/577305-sklum-scand-metal-chair-foot just scaled down to 95%
Just basic rounded over cubes to raise the table to a better position. You can adjust how much additional height you want and how many screw holes to use (1-3 for the outside and 1-5 for the inside). I glued the feet on but still used the…
3D printable topographic miniature of Frankfurt, Nordend - 🇩🇪 Germany Capture the beauty of Frankfurt, Nordend 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates…
