P
Printablesdanbst
AOS5 DJI O4 Dual Antenna Mount
DJI Dual Antenna Mount for AOS5. Fits well with my AOS5 ELRS Antenna Mount. Can be used seperate or combined.
- Downloads
- 249
- Likes
- 4
- Rating
- 0
Search results: os5
22 models
P
PrintablesQuadamoose
AOS5 DJI O3 Antenna Mount
35° antenna mount with 32mm post spacing, designed for the DJI O3 antenna and AOS5
- Downloads
- 205
- Likes
- 9
- Rating
- 5
P
PrintablesT3000_FPV
AOS5 Antenna Mount Walksnail/ELRS
Mein erster Versuch einen Walksnail/ELRS Antennen Mount für einen AOS 5 Frame zu konstruieren. My first attempt at constructing a Walksnail/ELRS antenna mount for an AOS 5 frame. Print Settings Printer Brand: Creality Printer: CR-10…
- Downloads
- 124
- Likes
- 6
- Rating
- 0
P
Printablesdanbst
AOS5 DJI O4 Camera Mount
Camera Body Mount to mount DJI O4 Camera to AOS5 standoffs. 15 Degree tilt. Use in conjunction with my DJI O4 Lens Cap for full protection(ish). Print without supports.
- Downloads
- 104
- Likes
- 3
- Rating
- 0
P
Printablesdax.neal
AOS5, Chris Rosser AOS 5
There is a Hero 8 & Hero 9 GoPro Mount, with USB-C battery mod, dual and a single antenna mounting options, and a skid/arm protector for the AOS 5 frame. I added support to the antenna mount to address potential harmonics from the…
- Downloads
- 54
- Likes
- 1
- Rating
- 0
P
PrintablesQuadamoose
AOS5 Walksnail Antenna Mount
Two different models, a 35°/90° mount, and a 35°/125° mount with 32mm post spacing designed for the AOS5 and stock Walksnail antennas. One antenna sticks out for the best signal, the other stays close to the frame to keep it less vulnerable
- Downloads
- 53
- Likes
- 5
- Rating
- 0
P
PrintablesCadme1ster
AOS5 V2 combined GPS/GoPro Mount
I wanted to be able to install a GoPro AND a GPS on my AOS5 V2 frame. Since I don't like GPS mounts that extend out of the back of the quad, I designed this integrated GPS/GoPro mount for the front mounting patter (32 x 32 mm) of the AOS5…
- Downloads
- 53
- Likes
- 2
- Rating
- 0
P
Printablesdanbst
AOS5 ELRS Antenna Mount
ELRS Antenna Mount for AOS5 Frame. Print without supports, easy fit with no need to remove IPEX connector from receiver.
- Downloads
- 45
- Likes
- 1
- Rating
- 0
P
Printablesdg fpv
aos5 v2 walksnail gps mount
gps mount for the official walksnail gps
- Downloads
- 45
- Likes
- 3
- Rating
- 0
P
PrintablesPcDoc
VTX+ELRS antenna mount AOS5 EVO
The original antenna mount does not hold the ELRS antenna and mounting it horizontal is not ideal. This holder allows to hold the VTX antenna (in my case the Walksnail HD Pro Kit) and the ELRS antenna (in my case the Radiomaster RP1)…
- Downloads
- 40
- Likes
- 0
- Rating
- 0
P
PrintablesRaja
AOS5 V1 TBS M8 GPS with GepRC super buzzer mount
Print in TPU, 3 walls 0.2 or 0.3.
- Downloads
- 30
- Likes
- 1
- Rating
- 0
P
Printableskasesag
POS5000 SSD Adapter
POS5000 ssd adapter. Adapter for 2.5" SSD drive for POS5000. I adapted source model for the case of POS5000 in a way that you can safely plug SATA cables. Printed using PETG filament with 15% infill.
- Downloads
- 27
- Likes
- 3
- Rating
- 0
P
PrintablesPirinaka
AOS5-5.5 TPU Hardware
Set of printable TPU hardware for Chris Rosser's AOE5-5.5 quad frame. It consists of a DJI antennae set support and motor cable protector of various lengths (described on file name). Print Settings Printer Brand: Prusa Printer: I3 MK3S…
- Downloads
- 26
- Likes
- 4
- Rating
- 0
P
PrintablesPcDoc
Thumb Pro mount for the AOS5 EVO
This mount will allow you to attach a Runcam Thumb to your AOS5 Frame. If printed in anything else than TPU the two screws will be enough. If TPU is used I recommend a cable tie in addition to the screws. The attachment is a bit off…
- Downloads
- 25
- Likes
- 1
- Rating
- 0
P
PrintablesSir_Lancelot178
AOS5 GoPro 7 30° Mount
AOS5 GoPro 7 30° Mount. TPU Recommended
- Downloads
- 23
- Likes
- 2
- Rating
- 0
P
Printablesdax.neal
AOS5-5.5, Chris Rosser AOS 5.5
TPU Hero 8 & Hero 9 GoPro mount with USB-C battery mod. Added two more mount versions for the Hero 8 & 9 but with a groove in the mount to allow for the battery leads to run through the top plate. Added the DJI Action 2 mount Print…
- Downloads
- 21
- Likes
- 3
- Rating
- 0
P
Printablestearandfix
Adjustable angle attachment for Deemount EOS530 bicycle light
I bought a bicycle light on Aliexpress but it came with mounting bracket that points the light straight. It is ok if it is mounted in the center of the handlebar. But I needed to mount it on the side where the handlebar is at some angle.…
- Downloads
- 13
- Likes
- 2
- Rating
- 0
P
Printablesopcion3d
Base afeitadora Braun AIOS5
Base de carga para afeitadora Braun AIOS 5 Impreso en PETG No son necesarios soportes, pero si recomendables para un buen acabado final.
- Downloads
- 12
- Likes
- 2
- Rating
- 0
P
PrintablesJacob T
Vaporesso Xros5 Stand
Stand for a vape, pretty straightforward print. No supports. Will work for any vape that is roughly 24.6x14.5mm Prints fine in PLA, can be made very quickly due to simple geometry. I added 10 bottom layers and printed it at 10% gyroid…
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
Printableskasesag
POS5000 masking bracket for USB extension card (still WIP)
Masking bracket for powered USB ports found in POS5000 extension card. This model should be considered as WIP since It requires the removal of extension card and the use of masking tape or hot glue If you want to attach it to the back of…
- Downloads
- 11
- Likes
- 0
- Rating
- 0
P
PrintablesFurkan Basoglu
Delta Rod - POS5 - Filled&Tube
Suitable for POS5. There are 6 designs. You don't need support for printing. Print Settings Printer: Custom Rafts: Doesn't Matter Supports: No Infill: 0-25 Category: 3D Printer Parts
- Downloads
- 10
- Likes
- 1
- Rating
- 0
P
Printables
Base afeitadora Braun AIOS5
Base de carga para afeitadora Braun AIOS 5 Impreso en PETG No son necesarios soportes, pero si recomendables para un buen acabado final.