Search results: redlight

Counting matching models…

Shredlight 1000 wrist mount

i use 1" double sided velcro with it

Downloads: 51
Likes: 3
Rating: 0

Shredlights Various Mounts & Storage Organizer

I don't ride at night much so I usually just have them in my bag. I got tired of having to dig them out to use or charge, so I made a few things to keep them organized during transport or charging. The curved mount is a bit harder to make…

Downloads: 49
Likes: 7
Rating: 0

Order a print of this model

PrintablesModel Magic

Stargate Atlantis - Redlight Carrier - 2004-2009

Downloads: 46
Likes: 7
Rating: 0

Order a print of this model

PrintablesBenWin

Shredlights bike mount

This model is just a quick solution for mounting Shredlights to bike handlebars.

Downloads: 45
Likes: 2
Rating: 0

Order a print of this model

PrintablesTapirBlondeCactus

Shredlight Mount - Zip Tie Fitting

Different arrangement of the zip tie holes to suit my bike mounting need.

Downloads: 32
Likes: 3
Rating: 0

Order a print of this model

PrintablesFliCat

Evolve Hadean Shredlight Mount

Print with support, Shredlight mount side down. Use double sided tape to mount onto the rear belt cover.

Downloads: 25
Likes: 1
Rating: 0

Order a print of this model

Printablesablairlamb

Newbee 4GS Shredlight mount

Simple Shredlight brackets that slip over the top of the Newbee 4GS gear drive. Inside measurement is 22mm between bracket "legs". Best printed vertically with the slanted "tooth" part of the shredlight slot closest to the bed, with a…

Downloads: 22
Likes: 2
Rating: 0

Order a print of this model

PrintablesMikenopolis

AceDeck NYX Z1 Bullbar Shredlights Mount

***Made for Acedeck's NYX-Z1, the bar diameters are 21mm and they are 49mm apart center to center…not sure this will fit other bullbar specs. Shredlights' square truck mounts didn't work on this board with the bullbars installed, I…

Downloads: 22
Likes: 3
Rating: 0

Order a print of this model

PrintablesMikenopolis

Shredlights Bullbar Ziptie Mount (22mm diameter)

For those who can't seem to get the Shredlight's handlebar mount tight enough on bumpy rides, I made this one to utilize zipties. Just add a thin rubber layer then cinch it down as hard as you can. Hope it helps…I never ended up using…

Downloads: 22
Likes: 1
Rating: 0

Order a print of this model

PrintablesMikenopolis

Acedeck Z1 Bullbar Shredlight SL-1000 Mount

Another version of the compact mount. After getting my hands on a set of SL-1000+ light, I realized the light is roughly 30mm longer. I tested it on my original mount and it still works, but the SL1000 is positioned a bit too forward and…

Downloads: 20
Likes: 1
Rating: 0

Order a print of this model

PrintablesCorentin PIERRE

Shredlight inclined stand

After a year of skateboarding, my lights continue to dazzle others, which is why I created these simple but effective brackets with an 8° angle. Remixes are allowed and appreciated, for any suggestions do not hesitate. His models were…

Downloads: 13
Likes: 5
Rating: 0

Order a print of this model

Printablesablairlamb

MBS Matrix II Shredlight mount

Slight remix of the original MBS shredlight mount. The original didn't fit my SL300 lights (the light bottomed out inside because of the closed back and couldn't fully latch in. This version has an open back so the light can click in…

Downloads: 12
Likes: 1
Rating: 0

Order a print of this model

Printablesjvu4000

Adjustable Rails for "Anker"Lights (ShredLights Copycat) on eSkateboards

This is a design for a DIY lighting system for electric skateboards using picatinny rails, AR light mounts, and flashlights. https://forum.esk8.news/t/jvu2000s-ar15-anker-lights-shredlights-copycat/33388 This was made in Blender 2.82. The…