Counting matching models…
I have a few pieces of test equipment in my lab that utilize the common BNC type connector. The problem is that the connectors, when unused, are commonly left unprotected. Enter 3D printing. This little cap slips on and then twists to…
Instead of printing this one, use the updated model: The original model remains below in case anyone needs to replace a part for a mount that is already made. Looking for a new 12-bit scope I saw the new Rigols and liked the idea of the…
Wenn man am Auto,am Schaltschrank,an einer Anlage arbeitet und keinen Tisch oder ne Ablagefläche hat ,dann ist man damit gut bedient ! Mit dem richtigen Stativ kann man die Höhe und Neigung einstellen und jederzeit leicht drehen , Die…
Print 2 grippers, body with supports for the nut holes. 3 perimeters but infill can be light. Hardware: 10 M3 nuts and bolts 17-40 mm long. Longer than 25 mm will interfere with the power cord so only 9 can be installed. Also comes with a…
I wanted to protect my equipment from bumps in transit, or dust while not in use. I designed this to print in one pass on the bed of a Bambu Labs X1/P1, and that mean many others as well. Choose which side the device model labeling is on:…
When you use the retractable feet to tilt the instrument, the oscilloscope tends to slip or the feet collapse. With this model, you have the same angle as with the retractable feet, while the entire instrument is stable. You can also…
My oscilloscope is on a slippery surface and I have to hold it every time I press a button. So I designed a very simple mount that can be stuck to the workbench with double-sided tape. Insert the feet of the oscilloscope into the mount…
A stand for the Siglent SDS 1104X-E so you can mount it on top of the siglent SPD3303X-E power supply. does also fit for other models like the Siglent SDS1202X-E. designed in Fusion 360
If you like this model and use it please upload a like, it really helps others find it! I hated having my scope on my desk and the cables getting in my way, especially when not in use, and I already had a “portable” touch screen mounted…
This is a VESA mount for the Siglent SVA1000X / SSA3000X series of spectrum analyzers. I have tested it to fit my SVA1032X (same as the SSA3021X / SSA3032X). It grabs the instrument by the vent holes on the back, and provides bracing…
Adapter plate to stack Siglent SDG2000X on uni-t UDP3305S-E. Includes front and back adaptors/spacers and a step file for the right front bumper if you want to make another adaptor.
Over a year ago I uploaded SDS8xx VESA mount and it works fine, but I learned a bit from it. It took too long to print because it needed a lot of supports. It was too big because it tried to enclose the whole oscilloscope, so it didn't…
This bracket features 4 banana jacks to allow easier connection of loads and for easier access to the rear voltage sense terminals. Print Settings: 0.2mm layers. 20% infill PETG No supports But be sure the printing orientation is…
This is a device to extend the legs of a Siglent oscilloscope. I made it for a SDS1202X-E but I assume it would fit their other model. Post a comment if you find it fitting other pieces of equipment (although I still can't see people's…
I found this cool cover for a SDS2104X , but it doesn't fit my model (and no CAD model provided). So here's a from-scratch design. I prefer PETG. Add supports under the four pegs so that they are clean enough for mating the two halves…
There are lots of probe holders out there but all of them are too big to retain the probes that came with my SDS1104 scope. Includes fusion 360 design if you want to tweak the model. Prints flat side down in PLA with no supports needed.
This is a four-part print to add an accessories drawer (with two drawers) and a probe rack to the VESA mount I made for the Siglent SDS8xx oscilloscopes: Siglent SDS8xx VESA mount v2 . No supports are required during printing, if you…
https://cad.onshape.com/documents/f1d84935c189b4e6ca6b77e4/w/97386357dcd7eadf47824a91/e/eadc890d8ac4e32ea81bc50b Retaining feet that can be mounted to a surface to stop the oscilloscope from sliding or moving
I made my own from PETG - 5 perimeters, but other materials will work also fine. You need four pieces for single instrument.
https://cad.onshape.com/documents/34276c57ab8f636678834ea4/w/05c7eabcec21066782991bd5/e/58356f4aac95f63cfb5567c9 A cover for the calibration and ground reference terminals on the siglent sds1204x-e
Adapter plate to stack Siglent SDG2000X on uni-t UDP3305S-E. Includes front and back adaptors/spacers and a step file for the right front bumper if you want to make another adaptor.
