Counting matching models…
Disclaimer: This model is a WIP, has not been tested in terms of durability and is likely going to change. Throttle Mount: Insert M4/M5 Nuts into the adapter Screw HPR to printed part using the provided metal-mount and screws Screw…
I finally broke down to tune my brake pedal for my Simsonn Pro Pedals. There are additional elastomers and springs in the kit, and I wanted to soften the initial press, with a nice progressive increase. Problem? The included springs are…
This is a mounting solution for the Dayton Audio TT25 puck transducers for the Simsonn Pro pedals. I remixed Barracuda72's original design so that it was one printable object instead of separate components. This modification necessitates…
15/12/24 Update: - Added a new throttle pedal replacement face, currently i designed it around some round head screws i had on hand as i didnt have enough M5 countersunk bolts that were long enough but i will update this at a later date…
I sim race in socks, so found the brake pedal on my Simsonn pedals to hurt my feet a fair bit. I couldn't find any replacement brake plates and the ones I did find were more than I was willing to spend. So I set out to make my own,…
Inspired by: https://www.printables.com/model/660092-sim-jack-pro-pedal-speaker-mount Adapter to mount 50mm Resonance Speaker to the Simsonn Pedals Brake. I assumed Simsonn Pedals were more or less the same as the Sim Jack Pro Pedals,…
This is a remix of user "mwmwmwmwmw" simsonn's pro pedal control box mount. centered tabs, reduced hole diameter for m3 SHCS mounting. and added an opening for the ground wire to come out opposite side of the pedal connections. I also…
I was not happy with the softest set of elastomers that came with my Simsonn Plus X pedal set, so I designed a softer set for use with socks. I printed them in Creality CR-TPU (95A shore hardness) with 20% gyroid infill. Adjust the infill…
I made these from scratch for the Simsonn Pro X Ultra pedals, the other designs on this site and others didn't match the distance between the mounting bolts (67,5mm). The motors mount with M4 bolts in a 19 by 28mm pattern, the throttle is…
Mount for a Haptic Transducer on the accelerator pedal for SIMSONN Pro pedals
Simple pedal specific heel stoppers that snap into pedal main pivot screw. No tools, disassembly or alternations needed. Designed for Simsonn Plus X pedals, but most likely work with other brands too. The design allows them to pivot a…
All same as original, with different side plates to fit Simsonn Pro Plus pedals. Please find all other required parts for the heel rest on the original design page. Note: Unlike the original, you will need to print the left and right.…
Compatible with SIMSONN pedal pads Requires PTU printing
This is really straight forward. Do you have a wheel stand, a cheap one, and the pedal plate doesn't have all the slots you need to mount your pro pedals? I came up with these drill guides. The clutch and gas pedals have the same foot…
Replacement plate for a Simsonn 7 speed shifter that blocks off 7th and makes it harder to misshift into reverse. The stock top plate also lets the shifter rod slam into the PCB during use, this should stop you from damaging the PCB while…
Cup attaches to the base with 2x M3 screws. Base rests on pedal bolts and optionally glued to plate with double sided sticky tape. Included base variants for throttle and brake.
it slides onto the metal pin in the simsonn pedals brake, use hot glue to attach the controller module. UPDATE - I ended up inverting the mount, when you press on the brake it pushes the parts up like a hinge, and they make a small noise…
This spring holder initially created for this VRS throttle-mod https://www.thingiverse.com/thing:6667011 , but it can be used to change the original spring holder in which have a bad tolerance, causing some compressed metal noise on the…
Description A custom ergonomic heel stop designed and tested on the SIMSONN Pro X Ultra load cell pedals. Because SIMSONN shares core geometry across its series, it should also work with other models in the lineup. The mounting wings…
I bought a set of pedal shakers from Simsonn for my Fanatec CSL pedals but could not find mounts so here you go. This mount is compatible with the VAM Pro, Neo, and V2 motors. Because of the orientation it is best suited for the VAM Pro…
I could not really find pedalplates fot the Simsonn Pro X Ultra, so I made some myself. Pretty simple design, but i works great. Printed in PETG with 20% Infill
This is a remix of Martin Majewski's design , specifically overhauled for the Simsonn VAM Pro haptic motors. The goal was to create a rock-solid connection between the motor and the Fanatec CSL pedals to ensure 100% vibration transfer.…
Small plate to mount the simsonn plus X box on a 4040. Use a M6X16 contersunk screw and on of the M- screw of the Simsonn kit for the other side
I modified the original plate design, to delete the 7th and reverse gear when not needed. You just have to unscrew the top cover of the Simsonn HS-Pro to change the plate. Link to the product page:…
Designed for Simsonn HS Pro Compatible with Amazon handbrakes Works with GT Lite and F-GT Lite Works with Logitech G920/923 shifter as well I printed it with Polylite ASA 10 walls 8 top/bottom layers 25% gyroid infill Hardware: Uses…
Adjustable steering damper spacers.
This is a custom 3D-printed mount for the Simsonn VAM Pro Linear Motor (Pedals Haptic Reactor), specifically designed for the GT Omega Classic V2 bucket seat. It fits perfectly into the mounting hole for the seat belt between the legs,…
I use a Simruito type handbrake with Simsonn Controller . The Simruito factory controller was faulty, the connection pins are the same as the Simsonn pedals. I made an extension box with a 3D printer, because the Simsonn control box is…
I modified the original plate design, to delete the 7th and reverse gear when not needed. You just have to unscrew the top cover of the Simsonn HS-Pro to change the plate. Link to the product page:…
