Counting matching models…
Mount your Mean Well power supply (PSU) model GST60A09-P1J, GSM60A09-P1J, or GSM60B09-P1J (125 x 50 x 31.5 mm) to your wall, shelf, or cabinet using #8 flat countersunk screws. Use Spax #8 T-20 T-STAR plus flat countersunk head…
Das Teil beseitigt ein grundsätzliches Problem dieses ansonsten perfekten Bandschleifers. Trotz eingeschalteter Absaugung werden bei weitem nicht alle Späne abgesaugt. Damit ist jetzt Schluss :-) Der Staubschutz wird einfach auf den…
This is the baby penguin from the game SM64 (DS remake as N64 used same model for baby and momma penguin). Please do not throw him off the edge of the map! I've made each colored region printable separately so that you can easily glue up…
Both models were made with slots to insert magnets for a easier deployment, making it also possible to retrieve the magnets if the print doesn't turn out so well. The size of the inserted magnets is 20 * 10 * 3 mm and they can be found in…
For my Scheppach OSM600 I needed a special angled adapter to fit in the corner of my shop. Therefore I designed a hose adapter which fits on one side on the maschine and on the other to a standard DN50 / HT50 or 50mm Hose. Print without…
Migrating from thingiverse https://www.thingiverse.com/thing:4600837 Arkon Phone Tablet Mount Slim-Grip Legs SM688 SM060-2 11.5mm wide, glued 1.5mm thick rubber on top. (30mm X 9mm) SM060-2…
This device was developed to be attached with double side tape to the machine. For additional protection, a board cover was made to fit in the ESP32-S3 support and allow the connection with the battery and the external sensor. The code…
Pièce de réparation mixer Bosch MSM6280/01 ; il s'agit d'un pièce intérieure en plastique retenant la partie rotative/basse du mixer. La pièce n'est pas parfaite ni totalement identique à la pièce d'origine, mais permet une impression…
This holder mounts to two of the standoffs in the front part of the mower. The standoffs are drilled and M3 heat set inserts (I used BOSSARD 1386743) are pressed in. M3 screws are then used to secure the holder. The PCB to the left of the…
osVAC Neo M32 adapter for Scheppach OSM600 Should fit any tool with 38,5mm outside diameter
I broke the front screen's hinge on my RØDE NT1-A's mount (apparently called the SM6 ), and instead of dealing with some weird imperial thread ( Untermenscheneinheiten ) I 3D modeled a replacement for M5 hardware. You need: A 5 mm drill…
Der oszillierende Banschleifer OSM 600 und vergleichbare Geräte werfen nach rechts Schleifstaub raus, der nicht direkt von einer starken Absaugung abgesaugt. Da oft das mitgelieferte Anschlag rechts nicht genutzt wird, damit mal auch…
This if for use with the 3rd generation Scarlett solo studio, I think the fitting is the same as the CM25 MkIII condenser microphone. This microphone has a recessed 22x1mm thread. The R0DE has a 20x1mm thread. You have to remove the…
Der oszillierende Banschleifer OSM 600 und vergleichbare Geräte werfen nach rechts Schleifstaub raus, der nicht direkt von einer starken Absaugung abgesaugt. Da oft das mitgelieferte Anschlag rechts nicht genutzt wird, damit mal auch…
I broke the front screen's hinge on my RØDE NT1-A's mount (apparently called the SM6 ), and instead of dealing with some weird imperial thread ( Untermenscheneinheiten ) I 3D modeled a replacement for M5 hardware. You need: A 5 mm drill…
A slime VR case for a LSM6DSV + 18650 battery, handwire and a rocker switch like a PSU one
The stand consists of 4 identical legs, held together by a central ring, four M2.5x30mm screws, and four M2.5x4mm heat inserts. On the top of each of the legs sits an angled magnet. Said magnet holds on to the microphone's shock mount's…
