20 models
POLARIS KEY COVER For RZR Ranger General Sportsman from TPU Two models: Wider top with place for adding personal name, this specific has my name on it, Slim top without place for personal name.
Seat Risers for the Oldtown PDL's will definitely give you a better angle for pedaling and also relieve the stress on you knees and back. Will fit the Sportsman 106 PDL and the Salty PDL. Material: PETG Infill 30% Perimeters: 6 Nozzle:…
Tool holders designed to attach to the outside of the side pockets of old town sportsman kayaks, made for the 106 PDL but should fit most of the Old Town Sportsman line. Heavily influenced by Bradget Designs on ETSY but I wanted some that…
NEW VERSION V5 Phone holder for Polaris Sportsman, the holder adapts perfectly to the dashboard and does not require any type of disassembly of any part for its assembly. Simply insert it under the handlebar and screw it with 6mm nuts,…
After frequent usage of the factory Oldtown Sportsman handles and getting in some precarious spots fishing saltwater marshes, the carry handles started to leave much to desire. Flex and separation of the 2 piece handle system leaves much…
These clasps will eventually fail on you (as this one did). I wouldn't even guess at how much the OEM would charge to replace them. My original in ABS did well (grey), and the second one in PETG (black) should do ok too. For strength,…
These are 1" seat risers for the Old Town Sportsman 106 MK or if your seat has a 22mm frame they should work, I'm not sure what size screws I used but it should not be hard to match some SS screws to it. Print Settings Printer Brand:…
Replacement suspension bushings for a 2004 Polaris Sportsman 500. There are probably other Polaris models that these fit. I purchased a set of these and they were made of hard plastic and I wanted to be able to print them in TPU so I…
I ended up with a used tote that was missing a latch, so I modeled one. I printed in PLA, 3 walls, 20% infill, and it is holding up fine so far. In the photos the black latch is an original Plano part, the grey latch is a printed…
JPG Design3D Washer for the flagholder found on various polaris models. The original holder has a pretty big hole. This washer is meant to adapt to smaler size screws. Print with 10+ perimeters and drill the hole the size you need. Inner…
This is a plug/cover for CVT hot air outlet hose during cleaning of Polaris Scrambler S / Sportsman S. Because of the direction and location of the original outlet in these models it is easy to flood the CVT mechanism and the belt. Just…
link for hex head bolt: https://a.co/d/0b14Shnz
Speedometer cap replacement for Polaris (sportsmann 2006). The speedos on these are known to fail so instead of buying a new speedo you can just print a cap to keep water out. Made it possible to zip-tie loose cables to the backside of…
made this file because i couldn't find a file for this ,, so here it is , NOTE!!!!!!!! this fits over the fuel filler cap , take off the fuel cap and insert this over and put the fuel cap back on. , Also , has to be printed with supports…
This is a simple replacement cap for the bumper tube. Print in any material and keep spares on hand.
This cylinder is sized for installation of a mechanical water pump seal on a 2000 Polaris Sportsman 500. It's a simple tool, but works much better than a socket. Print with PETG or PLA. It's an easy print that is intended for one time…
REAR STABILIZER TUBE BUSHINGS FOR POLARIS SPORTSMAN. PRINTED IN TPU-GF. FITS NICE AND SNUG NO ISSUES.
Replacement of: 5453258-070 KEEP IN MIND , that the model is quite big and you have to have the bed size at least 305 mm in one axis. I recommend to use Bambu H2D (the bed of it fits two of those). Required parts: 3x M4x10 bolts, 3x M4x6…
I ended up with a used tote that was missing a latch, so I modeled one. I printed in PLA, 3 walls, 20% infill, and it is holding up fine so far. In the photos the black latch is an original Plano part, the grey latch is a printed…
Replacement of: 5453258-070 KEEP IN MIND , that the model is quite big and you have to have the bed size at least 305 mm in one axis. I recommend to use Bambu H2D (the bed of it fits two of those). Required parts: 3x M4x10 bolts, 3x M4x6…
