Counting matching models…
Made a stash box with a built in rolling tray. The main hinge and the hinge for the latch are both print in place. I used 2 mm by 10 mm magnets for the tray cover and latch. Meet the ultimate weed storage box – it’s like the Swiss Army…
Mixture of a few files found here on Printables into one ultimate Ashtray. Photos to come. Printed with basic settings on BAMBULAB P1S, it came out just fine.
Made a stash box with a built in rolling tray. The main hinge and the hinge for the latch are both print in place. I used 2 mm by 10 mm magnets for the tray cover and latch. Meet the ultimate weed storage box – it’s like the Swiss Army…
When you're sitting stoned at the computer... I don't know why, but I made a pipe for my 14mm bong glass heads. Normally I would throw the design in the garbage can now... but in fancy filament and fuzzy skin it doesn't look bad at all...…
A playful and discreet container designed with chill vibes in mind. Smooth, minimal, and character-filled, this little stash buddy keeps your goods hidden while bringing a touch of humor and personality to your shelf. Perfect for those…
A blank, matte-white model of a super chill, red-eyed stoner cat. This DIY collectible captures laid-back feline energy in a smooth, minimal form—perfect for painting your own relaxed, spaced-out kitty with style and personality.
A blank, matte-white model of a spaced-out alien just vibing through the cosmos. This DIY collectible blends chill extraterrestrial energy with a smooth, minimal form—perfect for creative painting and fans of high-flying intergalactic…
Printed on TPU 95A since it needs to be flexible Needs to be printed on a softer material, since the bigger cherries get stuck.
Designed from scratch in Fusion 360. No supports needed. The model has 2 parts (body & pot) to allow for different colors. Inspired by: Tridant Joint Holder Towelie There is a 4.5mm hole at the top for any optional accessories (hats,…
Pot Leaf Base Stand for Blazer Big Shot GT 8000. May need scaling +/- 1% depending on your printers tolerances. I would recommend sanding the sharp points on the leaf tips after printing to avoid accidental scratching.
My take on the Stoner Unicorn card from Unstable Unicorns. If i see that it is popular, will do more :) Print instructions Model prints with supports at the tail end and at the front covering the chin, both elbows and the bottom of the…
remix of Stoner's Ashtray replacable screw tip for better ash remove and if ash is hot and tip was melted you priit just tip not all the ashtray
Cone tip and a curved cone tip. No supports needed, really… you can if you want. it printed the overhang functionally enough that i dont have an issue screwing them off and on.
A pretty crudely made Cosmo and Wanda as a Lighter and Cannabis. Feel free to remix and improve!
nice organizer for a rolling tray, brush, dosing capsules for S&B Mighty and much more
enjoy doing smash plantains !, jejeje everythign is possible with 3d Printing I printed it in PLA to test it, but is better in PETG or ABS more heat resistent. NOTE: I printed it in two different sheet because the firts time, that I tried…
This is a replacement for the plastic part of a metallic plum destoner. Print in PETG preferably. Designed in Solvespace
Here is a remixed M4 magazine stand configured to hold a Classic Army/Ares Stoner 96 AEG. It's chonky but does the job! No, it does not lock in place like your box magazine does because it simply doesn't have the hardware to do so. The…
I made a clip for the original box magazine of the Classic Army Stoner 96. The clip allows the internal reservoir ramp to stay at the lowest position while you fill up the box magazine with BBS. Is this necessary? No, but it sure has made…
This is a simple, friction fit, barrel lock for both the Classic Army and Ares Stoner 96 LMG AEGs. Maybe you're one of those that accidentally released your barrel in the middle of a game? Here ya go. Again, just a friction fit and it…
