Counting matching models…
1:1 Model of a 24Wh battery for ThinkPad T470/80 T570/80 and T25. It locks in place securely, the mechanism on the left latch works as intended. I made it because I mostly use my laptop on a charger/docking station but didn't want a…
2.5" Drive HDD / SSD Laptop Drive Caddy Disk Tray Bracket for Lenovo ThinkPad. Compatible Models: For Thinkpad T470 T480 T570, For Thinkpad P50 P51 P51S, For Thinkpad P70 P71 P72, For Thinkpad E460(NOT E470)， For Thinkpad E480 E485 R480,…
designed for T47 bottom bracket, maybe also useable for BSA 30 about 48/50.5mm diameter with 12 nuts PLA works better than ABS. did used it for disasemble a bottom bracket after some ride. Just for the one which dosen't quite tight…
Print with 3 walls. No brim required usually. f360 file included.
ORGANIZZATORE GT471 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
This is a smart card reader cover for thinkpads. It is designed for T480 but it should work on others too. To make it look perfect, sand with ~600 sandpaper. Height of thinner part: 1.25mm Height of thicker part : 1.5mm Print Settings…
Print with 100% infill, and use a headset bearing press to hold it against the BB. Then a pipe wrench around the block to tighten it. Didn't slip at all, and the plastic was not even deformed.
Bottom bracket tool designed with lasercut handle to install T47 Praxis bottom bracket. You could probably also 3D print the handle.. or edit the tool to have a specific socket. However, a small socket will probably be a weak point for…
This is a vertical laptop stand. It's also called as necksaver:) It's designed for Thinkpad T480 but you can use for any laptop which has proper dimensions. The second version is designed to prevent falling etc. But the movement…
This won't fit your normal T47 Bottom Bracket!!! Kactus t47 86.5 BB are 49mm with 16 grooves, normal t47 BBs would be 52mm with 16 Grooves. I only found the wrench type BB tool which I really dislike especially if you have only 2mm to…
ORGANIZZATORE GT475 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
CASETTE PER PRESEPE GT47 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
MODELLINO DI ABITAZIONE GT47 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X3 PLUS / X4 PLUS
ORGANIZZATORE GT470 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ORGANIZER GT478 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
Hi there! Finally getting around to uploading the UT47 v1 Kishy Signature case I designed last summer. This is the first keyboard case I designed, so it isn't perfect, but it came out pretty nice! You will need M2 brass heat-set threaded…
Simple stand for Thinkpad T470s. The laptop is standing vertically. I use 10% fill, layer height 0.28mm
Lenovo ThinkPad T470 Media Box Conversion This project converts a Lenovo ThinkPad T470 motherboard into a compact media server or NAS enclosure while reusing as much of the original hardware as possible. The laptop had a broken screen and…
I needed an easy way to remove a bearing from a bottom bracket. This is currently modeled for an Enduro T47 External Bottom Bracket with SRAM DUB (29mm) spindle. This was super basic to do via tinkercad. If you need a different sizing or…
Model is split in half at the middle so it fits my printer. 40percent club gnap case. Bought the keyboard half assembled without a plate so i made this contraption :)
https://www.printables.com/model/986596-t47-bottom-bracket-tool-16-notches doesn't seem to work with the Enduro BBs so I made this.
ORGANIZZATORE GT472 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ORGANIZZATORE GT473 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ORGANIZZATORE GT474 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ORGANIZZATORE GT476 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ARTE&DISIGN GT47 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Artillery Sidewinder X4 PLUS Laser: Mecpow X3Pro 10W
ORGANIZER GT477 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
ORGANIZER GT479 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante 3D: Anycubic Kobra S1 Combo Laser: Mecpow X3Pro 10W
shortened the tool and added flats for a large wrench and a hole in the middle.
ORGANIZZATORE GT47 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2
PARTI MECCANICHE FUSION_GT47 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2 / X3 PLUS
Given that I couldn't find any T47 BB tools with 16 notches, I made it myself. This is a simple threading tool for T47 BBs made to fit ratchet and torque wrenches instead of manually threading it yourself. Please note, the size of my…
