Counting matching models…
Our kids love this books! Unfortunately the pages suffer from the extensive use. Especially the front- and the back-cover get damaged and ripped out by the binding, the cover separates from the rest of the book. Repair Instructions Print…
Standfuß für einen tiptoi-Stift von Ravensburger, damit er aus kindlichem Chaos heraussteht. Der Stift steht auf dem vorderen Rand der Hülle auf, die Spitze hängt frei. Getestet mit aktuellen und älteren Stiften jeweils ohne WLAN.…
The Tiptoi Pen Holder is designed for both the new and old generation of the Tiptoi pen. It features two holes, one for the new pen and one for the old pen, and features the Tiptoi logo on the holder. It is printed using "lightning…
This 3D model represents a replacement protective tip designed specifically for the 4th generation TipToi pen. This tip ensures the longevity and functionality of your TipToi pen, providing a cost-effective solution for maintaining its…
As mentioned this is a remix of Spyder7022 TipToi Pen holder: https://www.printables.com/de/model/116818-tiptoi-pen-holder-for-ikea-flisat-childrens-booksh I removed the holder specifically needed for the mentioned IKEA bookshelf and…
My brother-in-law made this great tiptoi holder and I thought that there must be many others who would find it useful. So I asked if I could upload it. Printing profile: 100% infill no supports Weight: approx. 8,4g Filament used: PLA eSun…
Print in ASA with 3 layer raft, draft shield 2 loops, supports and 15% infill.
PLA, 0,2 mm layer hight. It is a bit tight, so you need to be gentle when assembling it.
Replacement tip for generation 1 TipToi pens by Ravensburger. If the tip of your TipToi pen is dented or deformed it may not work properly anymore. To fix the tip just remove the top most part of the tip until the opening is cleared…
To bring some order to the children's room :) Printed with Prusament PETG 0.4mm nozzle / 0.15mm layer height / 30% infill IKEA Bookshelf: https://www.ikea.com/ch/en/p/flisat-book-display-00290783/ TipToi Pen:…
The pen was always rolling around somewhere, so I made a simple stand for it.
*** German version below *** This is a rugged box, adapted to fit the newest TipToi pen from Ravensburger. The blue images show the new version, which has a more relaxed fit in comparison to the orange one. In the attachment is also the…
The axle-part on my kids Tiptoi globe broke. so I made a new one. Hope it helps someone.
My kids love the book series from Ravensburger that have that Tiptoi pen. Because they “love” these books so much the binding started to somehow “dissolve” ;-) Here is a print that you can use to fix the coil binding of these books again.…
This is a Remix, with only small changes. I thought the base was a bit to wide, so i chopped it. To fit the pen with the silicone case, I print it slightly bigger (7%)
It was time for a second TipToi, thus also time for a new double-holder. Prints easily without anything special. Enjoy!
Tip Toi raplacement parts Category: Toys & Games
I used this parametrizable model in order to fix some tip toi ringbooks after the cover has been detached from the rings. The two halfs slide in from above and below. Afterwards i glued them onto the cover with some superglue and secured…
The part between the spiral binding metal and the book cover is quite weak. It's just a thin cardboard. If the card board breaks, the whole book cover comes of. With this part you can reattach the book cover to the spiral binding. It's…
Pin up results in poor layer orientation, so I suggest printing it tiltet with a brim for adhesion… I added a thin version of the pin since the hole on my second-hand globe seems to be a bit wider so it did not fit for not-so-used globes…
A fixture to mount my sons TipToi pen to an ikea shelf (can't recall the IKEA name, but the vertical wood beam is 60mm x 15mm). Simply use two pieces of 1.75mm filament as pegs.
bei der Skadis version könnt ihr die Haken reindrücken oder wenn ihr sicher gehen wollt, Kleber benutzen.
Printable without supports. PETG is recommended.
The little ones ripped of all of the glue tapes we tried so I decided to remix the holder to screw-on to IKEA kallax. The holes are 3,2 diameters and the spacing between the wings is 3,7cm Printable without additional support.
