Counting matching models…
This is a remix of the weighted backplate design from aaextra44 on Thingiverse. I printed this in PA6-CF on my X1C and noticed the trigger would not function when the part was installed on the TX22. Through trial and error, I was able to…
This is a magazine loader/speedloader/thumb saver for my Taurus tx22. It fits all models of the taurus TX22's (standard, competition and compact). No support needed. I added a hole in the wing for a key ring after I printed it so it's not…
This is for adding 8 to your TX22. You will need to get a longer spring and a screw for holding the base in place. infill 15% gyroid .16 layer. https://www.blackdogmachinellc.net/5pk-9heavyspring.aspx
This is a slip-on spacer for use with full size 16 round magazines in a TX22 Compact. Nothing holds it in place other than friction, easy to remove if you're sharing mags between different TX22's. The photo of three mags shows (L-> R) the…
Wanting to use Taurus TX22 full size 16 round mags in your TX22 Compact? They fit, but leave a gap between the top of the floor plate and the bottom of the magazine well. Does that bother you? Me too, so I wasted a lot of time coming up…
I made this to enclose the lower portion of the 34-round magazines made by ProMag. They always looked a but funky to me so i made the lower portion look more like the grip of the gun itself.
Made after losing one. Hope this helps.
This is a pin for the mag follower of a tx22, I used the Pin from the 16 round mag to get the measurements. Functions well, printed on a bambu labs printer with .08 resolution.
Now with a nice tight fit on the mag. This works like the factory loader now, with a little larger exterior that might be easier to handle for you.
Who doesnt love the Taurus TX22?!! I Printed my remix this night and it looks wonderfull and smooth!! Thanks again to @Racoon Dev for sharing the .Step file <3!!
6/15/26 Finished version 1. Press fits tight and uses original rear sight screw to fasten it. Requires 2 M4 heat set threaded inserts. I used Yaocom inserts from amazon, but any of them should work as long as they aren't too long. Print…
This is made for a friend with some finger dexterity issues, for his Taurus TX22 16 bullet magazine. It allows him to easily load his magazine with better control.
S&W Shield-2 9mm & 45cal, and the Glock 43 mags work perfectly. Taurus TX22 has a wider base, it will not allow side-by-side storage. The single holder version works great with the Taurus. The prints are a better way to store firearm…
Taurus TX22 spring retainer. This retainer limits the standard mag to 10 rounds To comply with the Canadian limit. I took the measurements from the original retainer. You can find the files for the mags in many places including…
ALL FUTURE MODELS WILL BE SHARED HERE: https://cults3d.com/en/users/antirice/3d-models Taurus TX22 magazine holder for the Honeycomb Storage Wall. Holds 4 magazines. Print details (as pictured): Printer: FLSUN V400 Filament: Duramic white…
Print on side with angled portion of alignment posts facing towards the build plate Required Original Mounting Screw 2 - M3 Heat-Set Inserts/M3 Nuts 2 - M3x6 SHCS Recommended Settings .1mm Layer Height 4 Walls 99% Infill PLA+ Or Better…
I got tired of looking for a black loader in a black range bag so I copied the stock part and printed it in yellow. Nothing fancy here, print with supports.
Holds the trigger group in place so you can tap out the seer pin and install the pin.
Basic thread protector sized for the Taurus TX-22 threaded barrel extension, but will also work for other applications where a short and thin thread protector is all that is needed. PLA will melt - print in ABS/ASA or better.
Who doesnt love the Taurus TX22?!! I Printed my remix this night and it looks wonderfull and smooth!! Thanks again to @Racoon Dev for sharing the .Step file <3!!
This is my smoothed version of @RacoonDev_1258837 blocky TX22 lower. All credits goes to him!!! I share both his .Step file and my remixed smoothed .Step file!
This is a remix of the weighted backplate design from aaextra44 on Thingiverse. I printed this in PA6-CF on my X1C and noticed the trigger would not function when the part was installed on the TX22. Through trial and error, I was able to…
The Taurus TX22 magazines have an extended portion that covers the bottom portion of the magazine. Unfortunately, those are very hard to come by recently, but the ProMag 21 round magazines are not as hard to find. Everywhere online says…
Holds the trigger group in place so you can tap out the seer pin and install the pin.
Basic thread protector sized for the Taurus TX-22 threaded barrel extension, but will also work for other applications where a short and thin thread protector is all that is needed. PLA will melt - print in ABS/ASA or better.
backplate for a Taurus tx22, print standing up with supports for best strength
