19 models
I printed this with PETG and made the walls thick but you can adjusted to however you need. The original leg height is 65mm, the one I created is 105mm, but you can use the Fusion360 file to adjust it to your likes. The original screw…
Print approx. €4.44–€5.43 excl. taxPreliminary estimate for PETGSource material: PET
Our IKEA VIMLE fold-out sofabed has removable seat cushions and back cushions. The area underneath the seat cushions is a very smooth consequently, the cushions "creep" forward whenever you sit down, stand up, or squirm around, leaving…
Couch Cup Holder designed for ikea Vimle
Cup & remote holder for the IKEA VIMLE sofa/couch (standard width armrest). Uses a printed Skadis board to allow for flexible attachment of holders. I deviated from the original Skadis hole geometry very slightly to make the overhangs…
If you raise your sofa, you will also need to adjust the fold-out bed. Here are risers for 40mm No support No brim
I needed an extension for the feet of my ikea vimle sofa so that my robot vacuum can fit under it. I specifically adjusted the height to fit the Roborock S55 (newer models should fit also. It's a simple print in place model which fits…
Prevents the cushions from sliding/creeping forward.
Spacer to put the leg of IKEA VIMLE sofa in so it stays 10 cm off the wall.
pour rehausser le canapé de 35mm pour pouvoir passer l'aspirateur dessous et être mieux assis pour le numéro 1 il faut 6 pièces et pour le numéro 2 il faut 4 pièces imprimées en PETG avec 10 périmètres , 10 couches supérieures et…
Is your sofa wobbly or does it just need to be raised a little? Here is the solution. First print the test file and test if it fits to your model. Then select the desired height and print it out. Insert the riser into the original foot.…
I found that the feet that Ikea used with the Vimle Sofa bed were quite sharp and were tearing up my floor. I have created these feet. The Middle feet completely replace the feet that come on the sofa bed. The End feet go on top of the…
Simple print. No support. I have adjusted the undersides of the holders accordingly. You can find a larger version here: https://www.printables.com/model/1107906-command-station-for-xtouch-for-ikea-vimle
à imprimer en PLA ou PETG n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
This fully parametric sofa armrest tray is inspired by an award winning design from R&DStudio . I built this smaller version from the ground up in Fusion 360 to provide a hobbyist-friendly model that fits comfortably on the build plates…
Sorry, only for bigger printers. ;-) You can find the version for smaller printers here . The storage area is much larger and there is the possibility to store two TV remote controls. 242.5mm length - 198.46mm width - 67mm height The head…
pour fixer la lampe hue play a l'arrière du canapé il faut 2 vis de 3,5x12 mm à tête fraisée n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir Bon Print !
Created a ventilation cover for IKEA's VIMLE footstool to close it up so small ( like LEGO parts ) items won't fall out the storage. Added a "connector" to join the parts if you need to split them to fit on your printbed. Just add it,…
Is your sofa wobbly or does it just need to be raised a little? Here is the solution. First print the test file and test if it fits to your model. Then select the desired height and print it out. Insert the riser into the original foot.…
à imprimer en PLA ou PETG n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
