253 models
Here is bench x200!! I recommend slow printing speed any filament Enjoy!!
Print approx. €11.69–€14.29 excl. taxPreliminary estimate for one variant
Stackable box 150x200mm Printed with PLA Layer height: 0.1 or 0.2 or 0.25 mm Perimeters: 3 Infill: 15%, Archimedean Chords Supports: no 2x Stackable box 150x90mm can be added to the top. Blank label - add your own text on top, print with…
Print approx. €0.09–€0.11 excl. taxPreliminary estimate for one variant
This space saving hexagon pattern basket system should do the job! Just print and forget, remember to turn the speed down if needed. You can stack baskets on each other with or without the lid - They stack BOTH ways!
3D MODEL DESCRIPTION Since the space of my desk getting lesser and lesser… so I have think of a effective way to re-organise all the tools and other stuffs… Pegboard is a fancy way to keep the things organised as we can mix’n’match the…
You can use these squares to easily level your bed. Print them out and then adjust each corner individually. If the surface is rough, lower that corner and if it's not sticking at all or you see gaps between the lines, then raise that…
IKEA Skadis inspired (compatible) peg board that takes up 200x200mm.
Used for testing bed level. After noticing defects in the first layer using PETG, this is a helpful guide to achieve smoother results. I suggest sizing down by 50% or even 35% to speed things up. Level bed with the knobs Re-Calibrate Z-…
1st layer test by 0.2 layer height
Nature Wall Art with 2 deer and 3 mountains The full model is 600mm wide, 300mm high and 3mm thick. There are also pre cut parts so it can be printed on smaller printers 200x200 and can be assembled later. I suggest assembling with glue…
This is the V2 version of SeanKFields Shore Trooper helmet. All credit for this model goes to him I merely chopped the files to fit my bed. The original files (including the armour) can be downloaded directly from…
Just another bed leveling grid. I've seen several, but I wanted to put a little more on the plate for a test print. Probably overkill, but it works. The print May have to be scaled a bit for your profile.
Wall-hanging double shelf with Honeycomb Storage Wall (HSW) sides to store more things.
Here is the Pixar Luxo Jr lamp totally 3D printed on 200x200mm bed and with led light ! To realize it you need white PLA for all parts except for : Join rods : you can used for it american fridge's pvc pipe (1/4"pipe) Light : you need a…
Tired of wasted vertical space in your fridge? This stackable organizer box helps you make the most of every shelf. Design highlights: Split into two print-friendly parts — no supports required Optional stacking connector — print only…
Vents are expensive so i thought maybe i could print it myself. I came up with this model after printing few variants and fixing mistakes. You can put it on doors, printer enclosures, dehydrators, pretty much anywhere where you need…
This is a two tier latched container box for storing 200 count 9mm lugers. Compact storage for use when going to the range, for example. The box is not designed with a locking point as it's a moot point if one can just smash it open…
Bigger is better, amiright?
L - profile 50x50x200 The profiles can be glued together - the profile in the attached photo is 1 m long.
a simple 200x200mm leveling test with 5 squares. disable skirt/brim for a faster print
I've only uploaded the files I changed, the others can be obtained from Hex2000's post. Note: you may need to change your infill settings to get these to balance just right. It was a bit of trial and error for me.
This model is a test for Ender3 CRTouch issues. In particular, the Y-offset on the probe caused a compounding error in the mesh. This issue will be immediately apparent along the vertical axis. One half will be good and another either too…
Tank trooper helmet by Sean Fields, not my design, I've just split it in meshmixer to fit my printer. Only the first 6 files required splitting. Original files can be downloaded from shoretrooper.co.uk Happy Star Wars day :) UPDATE: Made…
Filament leftovers trash / recycle bin (approx. 100x100x200mm). Have fun to print ;)
STL file of the legendary Sony VX1000 loved by all skaters.
einfache Quadratische Schale original 200x200x28mm. Natürlich nach belieben skalierbar.
Bitte prüfe vorher die Maß von deinem Kennzeichen und passe ggf das CAD an. Sonst kann es passieren, dass dein Kennzeichen nicht passt. Gerne könnt ihr mir die angepassten Versionen zukommen lassen, dann werde ich sie hier ebenfalls…
I always struggle to get the bed leveled on my Ender 5 s1. After making sure my Z offset is dialed in with a small square in the middle, I print this model for the corners and manually adjust the corners while this is printing. It's the…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Swap Instructions: Black until layer #8 at 0.72mm Pine Green until layer #14 at 1.2mm (Dark Green) Green until layer #20 at 1.68mm (Light Green) White for the…
This mask is specifically for the Meade LX200 8''. It is slightly oversized in order to fit 3 pieces of felt. Printed easy and fits perfectly. Thanks to Brent Burton for the generator! Print Settings Printer Brand: Creality Printer:…
I created a test grid for calibrating the bed up to 200x200 [mm] Thickness is 0.2 [mm] *The photo shows a 220x220 [mm] printer bed Dimensions of squares: 20x20 [mm] Line width: 2 [mm] Radius of a circle: 15 [mm]
Added build files for each section to print on Wanhao Duplicator 6 / Monoprice Maker Select Pro Ultimate
Calibration Cube (10mm to 200mm) – A precise tool for calibrating 3D printers, available in various sizes to suit different testing needs.
A replacement hard disk drive cover for X200-series Thinkpad laptops (X200 X200s X201 X201s). No raft or support needed, the horizontal notch might need a little bit of cleanup after print to properly fit. Category: Parts
This mod is an upgrade for my original Dynamic Balance Mod. See PDF
Small guitar body suitable for Electric Guitar Kit CST-24 Print Settings Resolution: 0,3mm Infill: 50% Filament: Maertz PLA Black&Blue Notes: (printable on a 200x200mm printer!) Category: Music
Thick Elegant Shelf Bracket with Arc Pattern I designed the bracket to use with shelf made with 2 scrap pieces of wood. Turned out a great project for my hallway! Dimensions: Arms: 210 x 200 mm Width: 25mm Note: Use Fusion360 file for…
A wall mount with a cut-out for routing a flat 90 degree USB-C cable from the bottom. Snap-on cover. Only 256mm wide so it can be printed with Bambu Lab printers.
Many thanks for Yanev for making such a grat box! Hovewer, after trying to customize it to fit FNIRSI DSO152, it occured to me, that minimal height of the bottom and the lid are 15mm each, a little to much for that small oscilloscope. But…
20mm 2000 pcs roll target sticker dispenser. printed in petg, no supports. 15-20% infill for private user. 100% infill for club use.
I designed this Glider in SOLIDWORKS for the Printables Make It Fly contest (18/02/2023). The glider consists of three easy & fast-to-print parts: Glider body Glider main wing - Should be rotated 45 degrees with your build plate is 200 x…
This model is an adapter from Vesa 100x100 to 200x200 , i used it to mount a tv on a Vesa 100. This model uses additional parts: 4x M4 Screws. 4x M4 threaded inserts (6mm diameter, 6mm length). I don't raccomend using this adapter for tvs…
Cosmetics basket 90x190x130/ 130x200x100 ŠxDxV (DxLxH) No support
200x200x200 test model wall 1.6 for 0.4 and 0.8 nozzle
Frame for Ninja turtle Hueforge Use supports Hueforge links - Make sure you get the 200 x 200 version Donatello / TMNT / Ninja Turtle / Wall Art / Multicolor by 3D Prints This Week - MakerWorld Leonardo / TMNT / Ninja Turtle / Wall Art /…
Print a back piece and then the frame itself, then sandwich the picture between them. You can use superglue to adhere the pieces together. The frames look especially nice if you use one of those carbon fiber smooth plates. Textured plates…
Creality K1 Max - Bottom Drawer - 300x200mm Features: - Ergonomic front handle (underside and top) - Spatula placement (on front-right) - USB space (on front-left) - Two other grid compartments for everything else *Wall thickness of the…
ALL-in-One!! Very fast print, and the HueForge print pops rights in! No additional pieces needed to print separately to hold the picture in place. Has spot to easily hang on the wall! If you would rather display it standing up just print…
SEE PDF FIRST. Mod uses McMaster-Carr parts. Print settings: .15mm layer height 3 walls 25% infill no support needed Feel free to ask questions here or IG at jd_sandman.
Flutebox is a desk organization system with a relaxed design with rounded flutes. A rectangular assortment tray 100x200 mm for pens, small tools and other knick knacks you need handy on your desk. Prints well in PLA, you can go low on…
si vous avez Besoin d'une grille pour remplacer de façon provisoire ou plus…! Impression recommander en PETG ou ASA remplissage a 100%
Material: PLA, PETG Print Settings: Walls: 3 Infill: 15% Gyroid Top, Bottom shell layers: 4
One of my first projects with HueForge, made it black and white to capture the contrasts better, you can use colors! Instructions for printing: Layer Height: 0.08 First Layer Height: 0.16 Color Changes: Black: Until Layer 9 Dark Gray:…
Technically not a remix but inspired by @xyren's blade cover. Plenty of X-acto knife blade covers on the interwebs but I couldn't find one that fit my X2000 blade holder, so Fusion 360 to the rescue. It has the same attributes as xyren's…
Framed R2-D2 HueForge Print This HueForge 3D print of R2-D2 brings the beloved astromech droid to life using four colors for a stunning depth and shading effect. Designed for versatility, it can be printed on both multicolor printers for…
Filp Text 2023- 2024 als Tischdeko und Partydekoration. Druckeinstellung: 0.16 mm Layer height, Supports nötig, möglichst mit Support Filament an der Stütz-/ Floßbasis. Falls Teile des Drucks beim Lösen des Supports abgehen sollten,…
TV wallmount with interface to VESA 200x200, I have used it to mount my 32" TV to the wall
Since the included ear pads of the MMX200 unfortunately tend to break quite often, I designed an adapter to mount the DT770PRO ear pads onto the MMX200. The adapter consists of two parts: Part 1 attaches to the MMX200. Part 2 holds the…
Silhouette of Toothless & Hiccup set in a 200x200x4.5MM tile. print feet also or hang it on a wall!
refrito malla skadis de 200x200x3 mm
Carburetor Spacer for Venturi Applications – for Vespa PX 200 and Vespa P200E This carburetor spacer is specifically designed for use in combination with a venturi intake. It ensures that the venturi receives sufficient airflow to operate…
Deutsch: Hallo Community! Ich freue mich riesig, euch mein neuestes Hueforge-Kunstwerk zu präsentieren – eine majestätische Eule! 🖼✨ Ich bin gespannt, wie es euch gefällt! Wenn euch das Bild anspricht, lasst gerne ein Like da – das…
Bin that fits in a Eurobox 400x300x200 box as a 2 piece devider Print instructions pla 0,3 mm works fine
Remix featuring adjustable joints for easy alignment and secure installation.
Simple lightweight mounting bracket 200x200x15mm for countersunk screws up to 5mm diameter. V2 is a more robust version. Print instructions Printed with PETG and layer hight 0.15mm. No support needed. Happy printing!
Couldn't find any frames I liked for some hueforge prints I did, so I created my own with a snap fit back. Theres also a recessed area if you want to include a note or business card inside the print. Fits 200x200mm. I've also made…
Zebra 200x200 frame Print with supports Link for hueforge Op-Art Zebra Portrait (Filament Painting) by Ian Smalley | Download free STL model | Printables.com Please "Like", review, follow and upload make. I spend a lot of time designing…
Maximize your workspace organization with this compact, 3D-printable IKEA Skadis-compatible pegboard. Measuring exactly 200x200mm, it fits perfectly on most standard 3D printer beds and is ideal for tight spaces, desks, or inside…
This is base part of ball clock project. The base is big part, that barely fits my Ender 3v2 printer build plate. It tends to warp (when printing at the edges of build plate), I cannot add skirt nor brim and with 0.6mm nozzle and 0.24 the…
Quick Bed Level check that takes under a minute and only 1g of fat!and that's with 1 skirt line. 200x200 No Brim/Skirt Line Height - .2 Line Width - .4 LARGER BED SIZE 300x300 here:…
Here is a lasercutter, I designed to cut and engrave some plywood, leather, cardboard and other materials. You will also need some 40x20 profiles, 3 stepper-motors with drivers, a lot ob GT2 belts, pulleys an rollers (all seen in the…
Just a solid body of VIVO X200 Pro Mini. Accurate enough to fashion DIY cases, holders, stands etc.
Here's another waterproof boxe to install some cables in it. As the shipping time was too long I've decided to print it with 3D printer. First 2 boxes were printed with PLA, should prevent water drops. Another attempt was made with ABS…
For T-Mobile's inseego's. Will work for both models. Organic supports didn't work for me 1/2 way thru, so used snug. Had to make it wide in back to allow for CAT5 plug. Tried to cut out some waste in the model to speed up print but all…
I've utilized the prints and info from @3DJourney for my Ender 3v2 to great success, and needed his 5x5 grid for my new printer, but I wanted more coverage, and needed larger squares to better recognize some of the issues with this…
Halter für deutsche Kennzeichen 220mmx200mm PETG, Flex
Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. Print Settings Supports: No Resolution: 0.2 Infill: 5 Notes: Infill 5% to allow it to flex a little bit, 0% also works. Wall count 3
Wallmount for the Samsung Galaxy Tab A8 X200 on a flush mount box. PoE to USB Power Suuply: https://www.sparkfun.com/products/18709
Air Arms TX200 cocking lever e clip removal and fitting tool infill 100% The clip needs to be rotated so the open side is up then put the tool over the clip and put your finger on the end to stop it slipping of then just pull. To refit…
Fanttik X200 (V10) Vacuum Cleaner Wall Mount / Hanger I originally printed the excellent “ Fanttik V9 Auto Vacuum Storage Case ” by Brim Reaper. It’s perfect for travel or camping, but I found that retrieving the vacuum and putting it…
Hallo zusammen, anbei eine Skadis kompatible Platte mit den Außenmaßen 200mmx200mm. Durch die kompakte Größe müsste sie auf die meisten Drucker passen ;) Eine Version hat Schraubenlöcher zur Befestigung an denen der Schraubenkopf bündig…
Remixed to be 200mm long, and mounted inside lid of drybox.
This is a mod for skirts for Voron 2.4 200x200 It is designed as a single print for each side. It does fit in a Voron 350 but you can cut if you need to fit it in a smaller printer. It embed the WaveShare 4.3 HDM Display
Fast test for your bed 0.2mm or 2mm height
Overall Dimensions attached in PDF All 0.2mm high Outer edge 200x200mm square 8x 15mm squares , with 5mm hole 1x 25mm square , with 10mm hole 2mm strip connects all the pads together, pull strip for easy removal The holes help me see if…
Vallejo paint rack for 7ml bottles 4 COLUMN PERFECT FOR 200 X 200 PRINTERS
Summary: Since I don't have a server rack, I created this cooling stand for the Ubiquiti UDM Pro SE. Note: The stand has a length of 460mm, width 330mm and height 50mm. The cooling stand can also be used for several other heavy devices. I…
No support is required if pot and feet are printed separately. However, both parts must then be glued together. A model has also been added where everything is in one piece, support is required here.
Im printing with a cubicon prime m22z. If you want to make it stand, print some simple feet (2x) Im making a whole bunch of tiles 20x20cm to stick to a wall.. so check more to come!
Customizable GeoMesh Panel 200x200 is a modular and flexible panel design that can be adapted to different projects and layouts. The base size is 200 × 200 mm , but the model can easily be scaled up or down in your slicer depending on…
I think that with a frame, it finishes Mario's portrait very well! You'll just need a dab of glue to hold it in the frame. → The portrait is available in the remix link below.
Center-feed paper towel dispenser 130x200mm Fits center-feed rolls that are 130mm wide and 200mm tall (or smaller). Separate wall bracket Printing No supports needed. Print all parts with the "flat side" down to ensure a simple print.…
A simple design of the rubber for the kick-start pedal of a Vespa or LML, valid for: Vespa P80-150X/P150S/P200E/PX80-200E/Lusso/'98/MY/'11/T5/Cosa also for LML Star 125- 200 2T/4T Printed in TPU 95A No Supports If you want a durable…
Small components parts tray for assembly/disassembly of equipment. Prints on MK3 MK4 print area. Filleted corners in base for easy removal of small parts even if you have fat fingers. Designed to use minimal material without being too…
A 2 bay QNAP NAS bracket for the QXP-W6-AX200 Wi-Fi card
Ce plateau rectangulaire de 250x200 mm présente une surface totalement plane, sans rebord, offrant une zone de pose dégagée pour de nombreuses applications. Idéal pour servir de base à des projets, de support pour objets décoratifs ou…
Self standing photo frame, vertical or horizontal. Easy to print without supports. Material PLA or PETG.
Bed carriage models for FLsun I3 2017 200x200 bed version (smaller one). There are two versions available: -with rounded details inside -without rounded details inside except R10 edges If you wish to print the drawings and cut the plate…
