Counting matching models…
This is a goodman handle designed for the XTAR D26 diving flashlight - it may also fit other models. You will need an M6x20-22 stainless steel bolt and a spring washer. You will also need some 4mm bungee cord. I prefer to print it with ~5…
This model is a wall mount for the excellent XTAR VC4 Plus battery charger, designed for Multiboard and Multiconnect . It likely will also fit the XTAR VC4SL , XTAR VC4 and XTAR VC4H which appear to have the same enclosure but I don't own…
A handle similar to a Goodman handle for inexpensive XTAR D26 torch for diving.
The XTAR PBS2 is compatible with 21mm and 18mm OD batteries (21700, 18650). As a result though, 18650 batteries can rattle loose when in motion and not make good contact. If you are only using 18650s, you can print and use this shim to…
Attaches by taking off the 2 pads and the the top strap (which are all attached with velcro to the back) and then pulling ithe top strap through the loop that on the back-side of the 3D print. Then just attach everything back as it was.…
This is a holder for the battery charger XTAR VC4 Plus to mount it on a French cleat wall. I printed it in PLA and I recommend using organic supports as shown in one of the pictures. To assemble you'll need M4x8.1 threaded inserts and M4…
XTAR VP4 Plus Battery Charger Magnetic Mount for IKEA Skadis Pegboard . This holder is specifically designed to be used with my modular camera charger station . Main Project Page: https://tinyurl.com/charger-station Modular Charger…
wallmount for XTAR X4 charger for 21700/18650 battery.
After printing @rdeknijf_2254512's excellent charger wall mount I realized that it was not the exact same model as mine (VC8S vs. my VC8 Plus), and thus was a little larger than what I needed. To keep it snuggled tight on my wall I made…
XTAR VN2 Camera Battery Charger Magnetic Mount for IKEA Skadis Pegboard . This holder is specifically designed to be used with my modular camera charger station . Main Project Page: https://tinyurl.com/charger-station Modular Charger…
Einfache Wandhalterung fuer das XTAR Dragon VP4Plus Multiladegeraet. Fuer beste Ergebnisse mit Stuetzstruktur drucken.
XTAR SN4 Camera Battery Charger Magnetic Mount for IKEA Skadis Pegboard . This holder is specifically designed to be used with my modular camera charger station . The design includes both 1-piece and 2-piece versions, allowing you to…
Adaptér akumulátorů AAA pro nabíječky XTAR VC2S.
The XTAR VC4SL has a slight issue with AAA sized cells that aren't completely bare at the negative terminal, this helps!
This is a brass catcher for the 9mm Extar EP9 pistol caliber carbine. It's designed to clamp to the top Picatinny rail. Holds about 70 shell casings. Included are the STL files for the body, end plate, and sliding cover. I'll add the…
I wanted to put some gridfinity battery holders around my charger, so of course I needed a gridfinity base to hold the charger!. Example printed in PETG
Remixed the model to use the standard multipoints, you can use smal/mid/big thread multipoint to mount the holder (Do not use light multipoint). Original model says it's for XTAR VC4 Plus, confirming it fits VC4 perfectly.
I made the print using PETG and 0.4 nozzle Either screw in the holder first or clip in the charger and screw in the holder into the wall (the charger has a good hole). Designed the gap between the charger and the wall, because I assume…
I made the print using PETG and 0.4 nozzle Either screw in the holder first or clip in the charger and screw in the holder into the wall (the charger has a good hole). Designed the gap between the charger and the wall, because I assume…
This is a housing that you can put around your XTAR XP4 Battery Charger to then allow you to mount it to a wall. Note that it's a tight fit. Some light sanding may be required though I didn't have to. Category: Tools
Print settings: Walls: 3 Layer height: 0.2mm (or bigger) Infill density: 100% (so that it is printed solid)
Wall mount for Xtar Dragon VP4Plus battery charger. Printed in PETG for a little flex and resilience, but PLA/ABS, etc should be fine.
edition of the original version. This one removes the need of supports when printing
A remix of Scorf's holder for the Xtar VC4 charger so it now fits the Honeycome Storage Wall. Supports are required to print the wall mounts.
Based on the Rugged Box Designed to house: 1x BAXXTAR Charger for SONY NP-FW50 Batteries 2x Sony NP-FW50 Batteries 4x SD-Card 1x Adater USB-C to Micro-USB
Holder for Xtar L4 Pro charger (don't know if other models fits) and place for 4 AA and 6 AAA akus.
When I first bought this charger, I noticed it getting very hot during 4-cell capacity testing. So I designed this cooling stand that cools both the cells and the charger while keeping everything at a comfortable 45° angle. Assembly is…
Protective cover for XTAR VC2 battery charger. Also good as protection against the bright display. https://www.amazon.de/gp/product/B00POZH9X2/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 Please print with not too soft TPU. When…
A decorative Stand designed exclusively for the XTAR VC2 battery charger. Holds ten 18650 Li-ion batteries (2 in the charger) and the USB charging cable. Prevents clutter. Prints without supports. Charger display is visible while in the…
I used the great work of @ME3D_619898 to make this simple holder for my akku charger. All prints without support Its for stuff that fits 35x115 mm
This holder is a friction fit to hold an XTAR VC8 lithium battery charger on a wall, or similar. It attaches with number 8 flat head wood screws. The model should be relatively easy to adapt for another screw size if that's necessary. It…
A simple xtar vc4 vertical gridfinity holder Also check the battery holder from Dalkain
Simple slotted divider box perfectly fit IKEA Skadis tray. The slot fit XTAR SN4/VN2 camera battery charger and extra docking.
I needed a housing for the batteries (NP-FW50) and the charger (Baxxter 18592 Dual Charger) for my Sony Alpha 6000. Layerheight 0.2 10% infill Printed in PLA
