Counting matching models…
Nissan 300ZX (Z31) Assembly required. Can be printed separately Use the pliers to separate the parts and then assemble the car. The model is on a scale of 1:64. To scale a model from 1:64 to 1:43, you need to use a scaling factor of…
I was gifted the Logitech Z313 computer speakers, however the satellites did not fit under my monitor. Laying them horizontally did allow me to use them, but they were quite unstable. Adding this little ‘shim’ holds it correctly in place.…
Filament: TPU Layer: 0.30mm Use textured metal sheet for better finish After printing, you can use a heatgun and heat it to make a curve for better fitment. Cool it in water or with cold wet rag in order to retain the curve.
Case for Microsoft Azure IoT DevKit AZ3166 (MxChip). I removed the Azure logo from the original design to make it more casual.
These are the plates to blank off the IACV, EGR, and Cold Start Valve on a Z31. These were designed and tested from an 88 300ZX Turbo, unknown if it fits other years or naturally aspirated cars, so do your own research. Print in PETG or…
The AIV is the Air Induction Valve that sits behind the driver's side headlight on the Z31. These two plugs are to plug the holes left behind on the intake boot, and to plug the line coming off of the AIV (the hose that comes off of the…
Needed a quick and dirty scan of a speaker to make a mount.
Version one is designed for single filament printers. Version two (MMU) is designed for multi material printers. Visit my website: https://StarLabs3D.com My YouTube: https://www.youtube.com/@StarLabs3D
This is a replacement Tension Rod Bushing for the 88-89 Z31 300ZX. The 88-89 Z31's are different than other years and it's much harder/more expensive to source bushings. This is based off of my measurements of a poly replacement bushing…
A replacement seal rubber gasket for the 1984-1989 300ZX. This replaces the crumbling gasket/seal found on nearly all Z31s. This could use some more refinement, but fitment is acceptable at this stage of development. Changes have been…
Filament: TPU Layer: 0.30mm Use textured metal sheet for better finish After printing, you can use a heatgun and heat it to make a curve for better fitment. Cool it in water or with cold wet rag in order to retain the curve.
Use these to cover the fuel gauge sender hole and the fuel pump hole. Insert your preferred cleaning agent into the fuel tank and shake.
Scanned the profile and then converted to svg then added the protrusion that engages the trim. Modeled after the clips used on the later Nissan 300zx Z31s
I keep my Logitech Z313 speaker base unit on top of my PC but I noticed that it was restricting airflow somewhat. I designed this stand to lift the speaker by 50mm to allow air to flow freely around it. I made it gothic style because why…
Z31 intake cover adaptor. For front facing Maxima intake to use normal z31 intake manifold cover.
Welcome to The Low Poly Auto Show! This is a Nissan 300ZX Z31. Print this model with NO SUPPORTS if your bridging skills are up to the task. Details/fit may not print as intended if the print is scaled down. Each remastered model is…
Use these to cover the fuel gauge sender hole and the fuel pump hole. Insert your preferred cleaning agent into the fuel tank and shake.
Scanned the profile and then converted to svg then added the protrusion that engages the trim. Modeled after the clips used on the later Nissan 300zx Z31s
I keep my Logitech Z313 speaker base unit on top of my PC but I noticed that it was restricting airflow somewhat. I designed this stand to lift the speaker by 50mm to allow air to flow freely around it. I made it gothic style because why…
This is a harness or vacuum hose clip for the Z31 300ZX, but I'm sure Nissan used it on other models. Apparently these are NLA and people want them, so I made a copy. PN#: 14962M or 24220B0701 Category: Automotive
