Counting matching models…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
Allows the mounting of picatinny accessories to the top slide of the ZWQ S200s Viper. Uses 4x M3 screws. You probably want some coarse thread countersunk ones for the longevity of the holes in the plastic slide, but I ended up using…
Some low profile rail options for the ZWQ S400 Zebra, pretty much as low as possible while keeping the front section functional. May not fit all picatinny attachments on the first 5 sections due to how close the rail is to the part. There…
Based of the stock butpad but increased to 45mm in length. please note that the end of the blaster isnt completely flat, so you might have to trim and/or shim the space between the blaster body and butpad for it not to wiggle around.…
This is a ring pull for the ZWQ Viper S200s that mounts to the top of the slide using four M3 bolts. There is a version for countersink bolts and normal cap head bolts. The ring pull sits low enough to not obscure the sights, but is still…
Cover plates for the exposed plunger tube on the ZWQ S400 Zebra/Red hare. Features a decorative topographical pattern of one of the fields I play at. Print with a brim if you have adhesion issues. I recommend adding some adhesive of your…
If you have a ZWQ s200s viper blaster that you have upgraded, chances are, it is difficult to adequately grip the smooth slide. In my particular blaster, I have installed a K25 spring, which makes it difficult to prime with its current…
no supports and no brim needed, also you should print it upside down
A rear angled free swivel QD point for the ZWQ S400 Makes use of the upper chicago screw that holds the magwell in place. Fits the threaded screw, not the internally threaded post. Ideally replace the screw with one of the slightly longer…
Should friction fit over the BCAR, if it's loose, let me know as my printer has pretty meh tolerances. The file has registration holes for ∅2 x 3 mm cylindrical magnets. Shouldn't require supports, print with whatever settings you like
Just a spring spacer for the s400. Scale vertically in slicer as needed. Use sparingly: You are likely to settle your spring with too much.
A replacement mag bumper for the thin, talon geometry, ZWQ mags. Fit is semi loose, I've printed these in PLA+ so I wasn't after a friction fit. I can add a tighter fir for TPU or other soft materials if people want it, just leave a…
No supports required, I printed in PETG but other materials should be fine. Friction fits into follower, you can use a small amount of adhesive if required, or scale the print to suit your printer. Fits a Ø6x6 cylindrical magnet or 2…
Shrub's Extra Edge bumpers for the ZWQ magazines
For me it's all about tacticool. So I made a suppressor shroud for the ZWQ BCAR. Depending on the kind of barrel you use, might need a bit of sanding. The body is tight fitting so that it stays locked in and not wobble around. Enjoy!
Just a shroud for the ZWQ 16 Bearings BCAR to make your blaster more tacticool.
Printed clips to mark your zwq s400 springs (These 3 are specifically from 604blasters)
A follower replacement for ZWQ mags, intended to give the spring more room roll freely. Regular and magnet (for dryfire kits) versions. This file is a WIP, feel free to leave change requests.
With all Lynx style blasters I always accidentally drop the mag by activating the mag release on my tac gear when I should the blaster. I modified the OOD model to take a ball bearing detent. You will need a 6x7 mm ball bearing detent.…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
Cover plates for the exposed plunger tube on the ZWQ S400 Zebra/Red hare. Features a decorative topographical pattern of one of the fields I play at. Print with a brim if you have adhesion issues. I recommend adding some adhesive of your…
A replacement mag bumper for the thin, talon geometry, ZWQ mags. Fit is semi loose, I've printed these in PLA+ so I wasn't after a friction fit. I can add a tighter fir for TPU or other soft materials if people want it, just leave a…
No supports required, I printed in PETG but other materials should be fine. Friction fits into follower, you can use a small amount of adhesive if required, or scale the print to suit your printer. Fits a Ø6x6 cylindrical magnet or 2…
A rear angled free swivel QD point for the ZWQ S400 Makes use of the upper chicago screw that holds the magwell in place. Fits the threaded screw, not the internally threaded post. Ideally replace the screw with one of the slightly longer…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
