Makita 18v Portable Soldering Station
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A portable soldering solution using a Quicko T12 powered by a Makita 18v battery.
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 53
- Wydruki
- 0
- Wyświetlenia
- 645
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Introduction
The goal is to create a portable soldering solution which can be powered from a Makita 18v battery.
This design uses a Quicko T12 STC Mini controller which is available for under AU$25 on Aliexpress.
Battery Capacity & Safety Warning
This device does not have any low voltage protection for your battery, so be mindful of run time so as not to damage the battery. My testing showed the device pulls about 2amps when heating on 18v.
There is also no fuse, so any wiring issues or other faults could start a fire/damage the battery.
Required hardware:
- 3D printed parts - I used PETG for all parts
- 1 x Case Top
- 1 x Case Bottom
- 1 x Front Panel
- 2 x Split Ring Half
- 1 x Battery Holder Left
- 1 x Battery Holder Right
- 1 x Iron Holder
- Optional 1 x Low Profile Knob
- Optional 1 x Box Base, Lid, latches and Insert
- Optional T12 holder https://www.printables.com/model/271938-t12-soldering-iron-tips-storage-case
- 1 x M3x16mm cup head screw (battery holder)
- 6 x M3x8mm cup head screws (front panel & frontmost battery holder to case)
- 2 x M3x12mm cup head screws (rearmost battery holder to case)
- 2 x M3x20mm cup head screws (case closure)
- 10 x M3 x 5mm heat set inserts
- 6 x M3 x 35mm screws for optional box
- Packaging foam for optional box
- 12mm power switch (latching 12-24v) https://www.aliexpress.com/item/1005006187833198.html
- Quicko T12 Mini soldering iron kit: https://www.aliexpress.com/item/4000577553855.html
- Makita battery terminal block: https://www.aliexpress.com/item/1005005625997327.html
Printing Notes
- I printed all components in PETG so it would be more heat tolerant as I expect to use this in outdoor environments.
- If you make the optional box, the lid, latches, base and insert are all printed as seperate components. The insert fits into the notches built into the sides of the box.
Assembly
General
- All the screw fixtures use heatset inserts.
- Aside from the Front Panel, assembly should be reasonably self explanatory.
- The controller wiring is documented on the Aliexpress item linked above, or you can refer to this Instructable: https://www.instructables.com/Hakko-T12-Soldering-Iron-Kit-Assembly/
- The iron holder simply friction fits to the case when needed. I wanted this part to be removable for transport. It's an adequate solution, but better options exist, such as the holder in this design, which I might incorporate into a future revision: https://www.printables.com/model/342703-milwaukee-m18-t12-soldering-station
Front Panel Assembly
The front panel uses a split ring to secure the aviation connector in place while still allowing disassembly if required in the future.
Before soldering the aviation connector to the PCB, pass the connector through the front panel, from back to front until the frontmost collar on the connector is clear of the front panel.
Place the split washer halves in the front panel recess such that the frontmost part of the washer sits under the collar on the aviation connector. Once the complete split ring is in place, secure the connector using it's own washer and nut against the rear of the panel (see photos).
Once you have the connector located in the panel, place the panel over the rotary encoder shaft and align the aviation connector studs with the holes in the PCB, then solder the connector in.
If you need to take it apart, loosen the nut on the aviation connector, remove the nut on the rotary encoder, then push the panel back towards the PCB so that the split ring halves can be pulled out.