Gondola v2 - Lightweight Fan Shroud for SV08 + BambuLab Clone Hotend
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
V2 tested and ready. Lightweight fan shroud for SV08 with BambuLab clone hotend. Removes rear 30mm jet engine fan.
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 48
- Wydruki
- 0
- Wyświetlenia
- 675
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
UPDATE 9/26/24
Gondola V2.1 is tested and ready. Ducts needed a bit of trimming to accommodate the pressure sensor. Z offset appears to be working fine, V1 and V2.0 caught their edges on the bed and skewed the probe pressure. Will be installing an eddy probe over the weekend, so I will inevitably be redesigning a bit for that.
UPDATE 9/24/24
After running some tests, I've started work on a V2 version of the Gondola shroud that includes nozzle visibility, airflow improvements, and extra cutouts for more weight savings and airflow to the heatsink. I was having issues with the edge of the shroud knocking over tall prints, so I've improved the contours and slimmed the whole package down.
While the fan on V1 was friction fit using a couple of pegs, they didn't print that well in PETG-CF. So I've cut them down a bit and added a M3 hole for mounting with hardware.
For V2, you'll need 6x M3x16mm screws. 4 are used to mount the frame to the toolhead, 2 are for attaching the fan.
Here's the Onshape for V2: https://cad.onshape.com/documents/68839830bc3e2fda6cefbd1f/w/3f8e7915d2257b8795a72569/e/73dd35970e54a529d7c6a191
###
Designed for a SV08 with Durozzle's TZ-style BambuLab clone hotend, PCD nozzle, and stock probe. Only tested on that configuration, but think this might work with the stock Sovol hotend and other BL clones. Might be space for an Eddy probe. Included a shot of my hotend sans shroud for reference. Please let me know if you test this in a different configuration.
The Gondola shroud offers 360-degree ducting, allowing you to remove the obnoxious jet engine 30mm fan and quiet down your PLA prints. (One day I'll design a dual 5015 shroud for the SV08 but this will have to do for now). Generous cutouts on the side provide airflow to the heatsink fan, whether it's stock (higher) or modified (lower). Going “topless” will also keep your toolhead MCU much cooler (if that's something you care about).
I ran a full battery of PLA overhang calibrations using a test model printed in PLA+ and didn't have any issues with melting. I'm pretty certain I would have if I were printing at PETG temps. Should go without saying when printing homemade fan shrouds: use PETG or better for heat resistance. Pictured model is printed in PETG-CF. You may want more if you print in an enclosure.
Use Voron settings:
.2 layers; 4 walls; 5 top/bottom; 40% gyroid infill
Use supports as pictured. You could use a support blocker on the mounting holes (top of the model) if you're really confident in your printer. Saves a few grams of filament and a few min.
Use M3x16 hardware to mount the shroud over the belt retention clips.
Onshape for your remixing pleasure: https://cad.onshape.com/documents/f7d0bf59421473a30534a6ec/w/43fe86acef8c27021a96bbd7/e/21fac6efe2226ca22769f8b0