EnXLosure top panel with fan, filter, pi cam, humidity sensor
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Top panel for enXLosure with pi and camera, box for fan with HEPA and charcoal filters, DHT-11 temp/humidity sensor
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 14
- Wydruki
- 0
- Wyświetlenia
- 271
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial
This project adds a filter with fan and various optional accessories to the top panel of the enXLosure by @Voxel3D. You will need the frame pieces as designed by @philon in https://www.printables.com/model/795011-enxlosure-5-part-top-panel and hex-grid.scad from https://github.com/charlespascoe/hex-grid .
The OpenSCAD file is configured around the size of the HEPA filter you obtain; in my case it is 155mm square and 25mm deep. After the HEPA filter is a chamber to be filled with filtration media of your choice, followed by a 120mm centrifugal fan. The photo shows a 12v fan in the containing box, this used a thermostatic control with separate power supply. I recommend instead using (as I do now) a 24v fan and a 'Clickmate 4' plug to connect the fan to the 'fan2' connector on the XL sandwich board so the fan is controlled directly by the printer. I also added a 'JST-2.54' 4-pin inline connector junction so the enXLosure can be removed (fan unplugged) without having to access the sandwich board.
The sliding panels for the activated carbon chamber aren't very tight, so I use tape to keep them in place - in use everything is held together by the outer box, but the tape keeps things together when the chamber comes out for media change. I use acid-free activated carbon and Nevermore Scorch (the purple pieces) to remove organics and provide an indicator for when to refresh the media. Using the XL fan control runs the fan less often than the thermostatic control, so saves on media.
I bought an air quality monitor and learned that I can smell pollutants before the device starts showing interesting levels. I can't smell anything coming from the filter while printing with this setup.
There is an optional stand for a Raspberry Pi with cutout for a camera, specifically in my case it is a 16mp ArduCam but I believe the plastic case is a standard size. The plastic cover of the camera is press-fit into the hole and angled as needed for the correct view. You may need to adjust the stand to fit your Pi case, and check how long your power plug is to avoid interfering with the filter box.
To avoid re-designing and re-printing for future modifications, several panel cut-outs with plugs are added around the fan box. The one nearest the Raspberry Pi has been modified here to mount a DHT-11 temperature and humidity sensor (probably DHT-22 is the better choice now, but this is what I had on hand). If I were doing it all again I would add a panel directly under the Raspberry Pi for this, but that's not the one I built so this is left as an exercise for the reader.
This project uses the Belfry OpenSCAD Library v2 (BOSL2) at https://github.com/BelfrySCAD/BOSL2/wiki, and I recommend calculating the $slop value for your particular filament of choice (and remember your shrinkage value from building the enXLosure). In my case I used CF-PETG (Tinmorry) which didn’t shrink at all for the enXLosure. The panels should fit snugly if printed in the same material as the top; there is an option in the OpenSCAD file to print a test piece and frame. I printed the panels in solid transparent PETG to allow light in; these shrank considerably, but this is OK as they just rest on top.
Here is a sample bill of materials; the links are just the ones I bought, not necessarily an endorsement:
24v blower fan https://www.amazon.co.uk/dp/B0DF32XLC1 plus mounting screws and locknuts
Clickmate 4 300mm cable https://www.ebay.co.uk/itm/126027947416 (I used the other end for https://www.printables.com/model/1101901-buddy-cover-with-fan-and-cable-tidy)
Nevermore filter media https://github.com/nevermore3d/Reseller
Geekworm Raspberry pi 4b case https://geekworm.com/products/raspberry-pi-4-heavy-duty-aluminum-passive-cooling-metal-case
Arducam 16mp autofocus raspberry pi camera https://www.arducam.com/16mp-autofocus-camera-for-raspberry-pi/
JST connector kit https://www.ebay.co.uk/itm/224247380543
Refer to https://www.printables.com/model/736656-xlcam-prusa-xl-raspberry-pi-camera for setting up the raspberry pi camera streamer with snapshots for Prusa Connect. I have included my files for reading the dht sensor and adding the data to the Prusa Connect snapshot.
These scripts are run from the admin_user's crontab:
@reboot /home/admin_user/bin/uploadsnapshots.sh >> /home/adm1n/snapshots.log 2>&1
@reboot /home/admin_user/env/bin/python3 /home/adm1n/bin/read_dht.py >> /home/adm1n/read_dht.log 2>&1
I recommend creating a /tmp2 ramdisk for the dht data and the snapshots so you don't wear out your micro-sd card. Do this in /etc/fstab:
tmpfs /tmp2 tmpfs rw,nosuid,noatime,nodev,size=256M,mode=1777 0 0