Truncated Icosahedron V2.0 (Hoberman Sphere)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
6,73 € – 8,23 € netto (bez VAT)
Dla pliku: F_Link_PRINT_TWICE_Qty_90+6_Extra_0.4n_0.1mm_PLA_MK4ISMMU3_9h34m.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 7,48 € netto (środek widełek).
- Masa podana przez autora
- 50 g
- Czas druku podany przez autora
- 9,57 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
100% printable - NO extra parts needed - snaps together! New and improved v2.0 with smoother action.
- Ocena
- 5 / 5
- Polubienia
- 42
- Pobrania
- 110
- Wydruki
- 2
- Wyświetlenia
- 950
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Engineering
- Licencja
- Creative Commons — Attribution
WARNING - CHOKING HAZARD! SMALL PARTS! KEEP AWAY FROM SMALL CHILDREN!
INTRODUCTION
This is a very satisfying sphere using the Hoberman mechanism. It is a truncated icosahedron, with 12 pentagons (5 sides) and 20 hexagons (6 sides) that expands from 20cm (8 inches) to 45cm (18 inches). It is based off of my original model: (https://www.printables.com/model/1112443-hoberman-sphere-truncated-icosahedron). I made a couple improvements - better aligned linkage which makes for smoother opening and closing, and combined the triangles and triangle caps into one bgcode/3mf file.
I designed this to assemble with NO glue, screws or melting filament for hinging - everything snaps together!
I printed this in PLA, which is what I have on hand, and it works great! I may be getting some PETG soon - if so I'll try it out.
This is a challenging build, which requires patience and dexterity. There are 600 individual parts (360 of which have supports) which take over 70 hours of print time, and a few hours of support removal and assembly. You can do it! I believe in you!
I apologize for the long instruction, but I felt it was important to make it as easy to understand as possible.
PRINTING THE PARTS / CLEANING
This project consumes 410g of filament including support material. For time I estimate almost 72 hours of print time (listed time doesn't count x2 F-Links), 2 hours of support removal and 2 hours of assembly.
I recommend printing all the links first - one batch of F_Links(PRINT TWICE), M-L_Links and M-R_Links. I print the second batch of F-Links while assembling the first batch of arms. Then I print the triangle bases/caps, as you can put together the second batch of arm assemblies (instructions below) while printing them.
The links are printed with custom supports, as they need to printed edge-on to prevent deforming of the pins and the sides of the links. The triangles and caps are printed with no brim or support.

These are printed at 0.1mm/layer - any thicker will make them messy and hard to assemble. I sliced it with extra parts, just in case you accidentally break one or two.
NOTE Make sure that the pins, pin heads and pivot pins are free of support material to make it easier to press the links together!
ARM ASSEMBLIES
- Start with (1) M-L_Link, (1) M-R_Link and (2) F_Links (shown in two different colors).

2. Place an M-R_Link with the pins facing up and place an F_Link over the middle pin as shown:

3. Using a flat block, press the F_Link down evenly onto the head of the pin:

4. Using a long pair of needle-nosed pliers on either side of the pin as shown, press firmly and evenly down to snap the F_Link onto the pin:

5. Repeat this process with the second F_Link, placing it opposite and upside-down as shown:
![]() | ![]() | ![]() |
6. Place an M-L_Link so that its pins are aligned with the two F_Link holes and assemble the same way:
![]() | ![]() | ![]() | ![]() | ![]() |
Check that the movement is smooth and that all links are fully joined. Repeat steps 1 through 6 - 89 more times. (did I mention this takes patience?)
ASSEMBLING THE SPHERE
Each arm assembly is an ‘edge’, joined with two triangle joints - one top/outer, and one bottom/inner. The two triangle joints are opposite one another.
Start with the top/outer triangle joint - place 3 top arm assemblies' pivot pins fully into the 3 slots of the triangle base as shown - It doesn't matter which end, as long as the arms curve with the outside (green or yellow link in the below picture).
![]() | ![]() |
Then place a triangle cap over the opening with the short bevels facing down. Make sure that one corner of the cap is fully inserted into the corner. Snap together using pliers:
![]() | ![]() |
Repeat this process with a bottom/inner triangle joint, making sure it is opposite the top/outer triangle joint.
ORDER OF ASSEMBLY
This is the same pattern as a football/soccer ball! There are 12 pentagons (5 sided) and 20 hexagons (6 sided). Each ‘edge' is an arm assembly, and each ‘corner’ is a top/bottom triangle joint.

You can start building from anywhere, but what helped me is that 1) pentagons(5) NEVER touch each other, 2) pentagons(5) are always surrounded by hexagons(6), and 3) pentagons(5) are separated by two hexagons(6). Above picture for reference.
I like to start by building a pentagon(5), and then building five hexagons(6) around it.
Give yourself plenty of space to work - there will be a lot of flipping the whole thing upside-down and back again to attach the top and bottom triangles, and it is floppy and sprawling during mid-assembly.
ACTUATION
When the sphere is fully expanded, it will not close on its own. Here's what to do:
Grab a corner on opposite sides of the sphere, and stick your thumbs between the inner and outer triangle joints. Gently force the triangles apart while gently shaking it and pressing inwards.
Like all things build with PLA, to will loosen up with time - which actually a good thing in this case, as it will open and close even more smoothly the more you play with it. I have several of these now, and NONE of them have broken or come apart from moderate fidgeting.
ENJOY A ONE-OF-A-KIND TOY!
I'm pretty sure that this is the ONLY hand-held truncated icosahedral Hoberman Sphere in existence. I hope you enjoy it as much as I do. Please hit the Like button, and I look forward to seeing your make!
Best of luck!
TroggPrinter











