1 / 5
Kabel / Transformerbox / LED / DUY / WLED 42 x 6 x 3 cm — zdjęcie 1
1 / 5

Kabel / Transformerbox / LED / DUY / WLED 42 x 6 x 3 cm

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Box for DUY electronic projects like WLED with transformer and ESP8266 or ESP32 where you need to secure the 230V side

Ocena
0 / 5
Polubienia
3
Pobrania
10
Wydruki
0
Wyświetlenia
47
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

I needed a box for my 230v to 24v transformer and my GLEDOPTO WLED conrtoller because it is sitting behind the couch and the live wire of the 230v side of the transformer was open. So I constructed this box in Plasticity.

Inner dimension are

420 mm long

60 mm wide

30 mm hight

Hole for the cables is 10mm diameter each. 

The lid is just put on top (it's not secured) and supposed to be used inside.

To print it on my Bambu X1C I cut the box and the lid in Bambu Lab with some dovetails so it fit's the bed of the printer. 

Print the box standing on its shorter side down (dovetail up) with some small raft (5mm) and you don't need any supports.

Print the lid with upper side facing the bed.

After printing I glued the pieces with two component epoxy glew.

There are the following files:

Elektrobox: stl with the whole box (420 mm long) in one piece

Elektrobox Deckel: stl with the whole lid (420 mm long) in one piece

ElektroboxKlein + ElektroboxKlein2: stl with box in two pieces and dovetails

ElektroboxKleinDeckel + ElektroboxKleinDeckel2: stl with the lid in two pieces and dovetails

Feel free to remodel to fit our use.

Ich brauchte ein Gehäuse für meinen 230V auf 24V Transformator und meinen GLEDOPTO WLED Controller, da er hinter der Couch steht und der stromführende Draht der 230V-Seite des Transformators offen lag. Also habe ich diese Box in Plasticity konstruiert.

Die Innenmaße sind: 420 mm lang 60 mm breit 30 mm hoch

Die Löcher für die Kabel haben einen Durchmesser von jeweils 10 mm.

Der Deckel wird nur aufgelegt (er ist nicht befestigt) und ist für den Innenbereich gedacht.

Um es auf meinem Bambu X1C zu drucken, habe ich die Box und den Deckel in Bambu Lab mit ein paar Schwalbenschwänzen geteilt, damit es auf das Druckbett des Druckers passt.

Drucke die Box stehend auf der kürzeren Seite nach unten (Schwalbenschwanz nach oben) mit einem kleinen Raft (5 mm) und du brauchst keine Stützen.

Drucke den Deckel mit der Oberseite zum Druckbett zeigend.

Nach dem Drucken habe ich die Teile mit Zwei-Komponenten-Epoxidkleber verklebt.

Folgende Teile sind vorhanden:

Elektrobox: STL-Datei mit der kompletten Box (420 mm lang) in einem Stück

Elektrobox Deckel: STL-Datei mit dem kompletten Deckel (420 mm lang) in einem Stück

 ElektroboxKlein + ElektroboxKlein2: STL-Dateien mit der Box in zwei Teilen mit Schwalbenschwanzverbindung

ElektroboxKleinDeckel + ElektroboxKleinDeckel2: STL-Dateien mit dem Deckel in zwei Teilen mit Schwalbenschwanzverbindung

Soll und darf verändert werden.

 

Tagi