1 / 5
Bearing Spool Holder for Prusa Enclosure w/MMU3 (Standard and 2kg Spool Options) — zdjęcie 1
1 / 5

Bearing Spool Holder for Prusa Enclosure w/MMU3 (Standard and 2kg Spool Options)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This remix refines and expands on the great work done by Hotdogger and sck_nogas. Thank you both!

Ocena
5 / 5
Polubienia
8
Pobrania
45
Wydruki
3
Wyświetlenia
397
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

I didn't want friction working against my extruder to pull filament and was looking for a good, frictionless, spool holder solution for my Prusa MMU3/Enclosure setup.  I was very happy to find sck_nogas' remix of Hotdogger's smooth bearing spool holder!  The only problem…it didn't support 2kg spools.  So I got to work and created this remix of a remix of a remix!  I hope you find it useful for your setup.

Recommended Print Settings:

  1. PETG, 0.15mm STRUCTURAL, 0.4mm nozzle (I like to print onto a textured, or satin, sheet when using PETG; I find removal much easier after it has cooled.  But any standard sheet will work).
  2. Bracket:
    • 25% infill for the standard version
    • 30% infill for the 2kg version
    • Supports are required for the arm overhang section
    • Use a perimeter of 3 or 4 (I found the post wall a bit too thin otherwise)
  3. Roller (both versions):
    • 100% infill
    • Supports are required under the first bearing stop ring overhang
  4. Axel (both versions):
    • 100% infill
    • A brim is required to prevent losing bed adhesion (I used 5mm)
  5. End Cap and Knob:
    • 15% infill
  6. Keeping true to the Prusa black/orange scheme, I chose to print stationary parts in black (bracket and end cap) and moving parts in orange (roller, axel, knob).  The provided print sheets were organized this way and were configured with the aforementioned print settings.

Required Hardware (per spool bracket):

  • 2x standard 608-2RS bearings
  • The remaining bolts and nuts needed you likely already have from your existing brackets:
    • M3x20 screw (x1)
    • M3x12 screw (x2)
    • M3nN Nut (x2)

Assembly:

  1. Carefully remove all support material from the roller, axel and bracket.
  2. Insert a bearing into each end of the roller and firmly push them into place until they are flush with the ends of the roller (a trigger-action bar clamp works well for this).
  3. For the 2kg roller, assemble the 2-part axel accordingly (male/female).
  4. Insert the axel into one of the bearings and gently push it through the roller and out the bearing on the other end until it is flush.
  5. Lay the bracket down onto a firm surface (with the post facing up) and gently push the axel all the way into the closed axel-receiver end of the bracket.
  6. Slide the roller along the remaining exposed axel until it is flush with the bracket and insert the newly exposed axel on the other end into the recess that will be covered by the end-cap.  Set this assembly aside for now.
  7. Remove the original bracket from the enclosure by undoing the two M3x12 screws holding it in place from inside of the enclosure (keep these to be reused).
  8. Remove the filament guide cap from the existing bracket by undoing the M3-20 screw holing it in place (keep to be reused).
  9. Remove the two M3nN nuts from the existing bracket and install them to the new bracket.
  10. Screw the filament end-cap you detached from the existing spool holder onto the new assembly using the M3x20 screw.  Do not over tighten;  this piece should be able to rotate freely.
  11. Attach the new bracket assembly onto the enclosure using the two M3x12 screws.
  12. Please your desired filament roll onto the roller and secure with the end cap and knob.
  13. Enjoy your new, nearly frictionless, filament spool holder in either standard or 2kg sizes!

Finally, another big thanks to Hotdogger and sck_nogas for their initial work on all of this!

Tagi