Cable Organizer / Routing Hook - Various Sizes
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
2,19 € – 2,68 € netto (bez VAT)
Dla pliku: LR2203-H-045-100 Example Print_0.2mm_PETG_MK3S_2h30m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,44 € netto (środek widełek).
- Masa podana przez autora
- 31 g
- Czas druku podany przez autora
- 2,51 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
A cable organizer, routing hook with locking ring for wall or ceiling mount. Designed for power cords or network cables.
- Ocena
- 5 / 5
- Polubienia
- 105
- Pobrania
- 291
- Wydruki
- 5
- Wyświetlenia
- 4084
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Office
- Licencja
- Creative Commons — Attribution — Share Alike
This is my design of a cable organizer or cable routing hook. It should provide enough space for many power cords and/or network cables. You will find object files for a wide range of heights and depths.
Orientation-wise it is made to be screwed to a wall, ceiling or under a table or furniture. There is a groove for a ring or rubber band you can use to close the hook after you inserted all cables. This ring holds the hook closed, even under a heavy load.
About the Design
I optimized the design to create good stability with minimal material use. The profiles are made for either a 0.4mm nozzle with 0.2mm layer height, or a 0.8mm nozzle with 0.4mm layer height.
A) There is a flat section with three screw holes you can use to fasten the hook to your furniture/wall. These screw holes also reduce the filament tension to prevent warping.
B) Starting from there, the hook has a groove to make it more rigid in order to hold heavy cables, with the least amount of filament used.
C) At the front, there is a groove for the ring to lock the cables in the hook. With a flexible material like PETG, you can easily insert the ring after montage. There is just enough space at the front, to push the ring into its groove.
The (printed) ring is held firmly in place after montage. You can easily unlock the hook, insert or remove cables and put the ring back on it.
How to Print the Hook
| Material | Print this hook with a material that does not deform over time, like PETG or ASA. Do not print this hook with PLA, the hooks will deform over time. |
| Layer Height | Use 0.2mm for a 0.4mm nozzle Use 0.4mm for a 0.8mm nozzle. |
| Perimeters | It is important to configure 3 perimeters for slicing! This will not only speed up your print, it is important to get the required stability. |
| Extras | If you print multiple hooks on the same bed, activate the option “Avoid crossing perimeters”, this will reduce stringing and optimize movements between the individual parts. |
| Brim | I successfully printed a large number of hooks without brim. Add one if you have adhesion problems. |
Dimensions and Part Numbering
You find models for many combinations of heights and depths. The heights are in the range 35mm – 100mm and the depths are in the range 80mm – 190mm.
These numbers are included in the part number, which has the following format:
LR2203-H-<HHH>-<DDD>.3mf
Where <HHH> is the height and <DDD> the depth in millimetres.
Montage
Use 3, 3.5 or 4mm wood screws and fasten the hook at least using the outer two screw holes. The third screw hole is optional, it increases the side stability of the hook.
For light loads, you can alternatively fasten the hook using strong double-sided tape.
Alternative Design
There is a round design with a slide-in lock:
Conclusion
I hope you find this cable organizer useful to tidy up your power or network cable installation. If you like it, please rate it and share pictures of your print.
Happy printing!
Explore More from Meti·kumi
Interested in my designs? Browse through my collection of 3D models:
👉 https://metikumi.com/3d-models/
Stay connected on social media for the latest updates and work-in-progress insights: