1 / 5
Skateboard wheel 127mm + hub version for 90mm motor — zdjęcie 1
1 / 5

Skateboard wheel 127mm + hub version for 90mm motor

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Can be used in an ordinary longboard or in an electric one. Compatible with belt drives, 90mm hub wheel or direct drives

Ocena
0 / 5
Polubienia
8
Pobrania
73
Wydruki
0
Wyświetlenia
255
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

This is an upgraded version of my previous 100mm design, now 127mm in diameter. It still has several features that makes it better than regular PU ones:

It has full tire groove for better grip, being 95% air inside helps in amortization (it's a lot more comfortable to ride on terrain at high speed), AND if it gets broken it is easily replaceable (just print a new one). Hexagon pattern on side walls helps building rigidity. 

Additional materials:

To assemble everything you need 6 4mm x 40mm screws (preferebly cylinder-shape head 7mm in diameter), 6 4mm nuts and 2 skate bearings. All that is for one wheel.

Make sure your printer is TPU ready before starting it. The wheel requires many retractions for your extruder to make, it's better you be certain it won't clog itself midprint. 

Important note: recently I tried printing tpu on pla speeds on my klipperized neptune 3 plus. It worked beautifully and only took 20h. TPU slow printing could be a relict for your printer too.

The core consists of two parts, both can be printed with PETG. I tried ABS at first, thinking it would be better, but after some tests I found out it has no advantage in daily use (my electric skate is perfectly ok after many miles on high speeds). 

Probably due to a filament/enviroment/printer the holes on the core parts can be either too tight or too loose. My recomendation is to print core parts first and test it with screws and nuts. Adjust the flow if needed, but your goal is only to make screws go through and meet the nut, holes better be a bit loose than tight. Don'use power tools when screwing in, nut can rotate in the channel, and you don't want it because it won't let you put in the screw. 

If your ball bearings don't fit you can use sandpaper or any other method to make the hole bigger. If it is too loose just put a drop of super glue and let it spread evenly around the opening so when it dries it makes bearing fit tighter. Either way tests show it's easier to fit it afterwards than trying to catch perfect size with scaling or CAD modeling (printers and filaments differ quite extensively in their “performance”).



Printing settings for tires:

layer height 0.2

outer walls 10 perimeters (probably you can go lower, but i wouldn't)

top and bottom 12 layers (it's enough)

infill 5% (heigher makes it denser, you don't want it. the tire should be flexible to absorb shock)

supports: none for abec, auto organic for hub version. make sure you use manual supports only for inner ring at layer 16, exclude hexagon area.

 

Printing settings for cores:

layer height 0.2

outer walls 6 perimeters

top and bottom 8 layers

infill 33%

no supports

otherwise use your average PETG settings

P.S. Wheels made out of TPU can be pretty tough, I deliberately “scorched” them on the asphalt to check. It melts up only reaching certain temps  but to make it happen you need to really grind them up in the same spot.

P.P.S. Make sure when assembling to follow the same tire pattern and to install wheels short core side facing each other on the axis. 

P.P.P.S. For all you hub motor owners, make sure your 90mm motor without sleeve can fit my tire. It's depth is 56.5mm and you could print some test fit. Just lower the model on a build plate halfway and print 10mm just so you could try it on. Wasting good TPU is pretty expensive. 

Tagi