Trading Card Flipper & Travel Case - Norin The Wary - Magic The Gathering
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Flips a sleeved MTG trading card over & over at the push of a lever. Addictively fun flipping action!
- Ocena
- 5 / 5
- Polubienia
- 28
- Pobrania
- 169
- Wydruki
- 3
- Wyświetlenia
- 3148
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Board Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
If you are a Norin the Wary EDH player and love outlandishly fun and completely unnecessary accessories for you EDH decks, then this card flipper is for you! I love playing my Norin EDH deck, but I was bored of repeatedly taking Norin in and out of play or covering and uncovering him every turn. Such a simple inconvenience obviously requires an impractical and over-engineered solution. Thus, I set to work on this “quality of life” improvement project.
I must admit, when I started this project, I was not expecting the result to be so satisfying, but the little boost of serotonin I get every time I push the lever is addicting (you have been warned). The design takes inspiration from lever actuated rotating grills. Its designed to work with a standard magic card in a Titanshield clear sleeve (though I imagine other sleeves would work as well). I suggest printing a fun message or image and slipping it into your sleeve on the backside of the card to surprise your pod when Norin flips over.
Of course, this flipper is useless unless you can transport it to your favorite game spot without it breaking. That's why I also designed a custom storage/travel case for it.
If you like what you see or make your own, please consider giving this model a “like” and/or posing your “make”. Thanks all and happy flipping!
REQUIRED HARDWARE:
Flipper
- (Qty. 4) M3X8mm screws
- (Qty. 4) M3X12mm screws
Case
- (Qty. 2) M3X12mm screws
RECOMMENDED PRINT SETTINGS:
Please note the following settings/parameters are recommendations and verified for PLA and PETG on the Prusa MK4S. If you are using a different printer or filament, you may need to scale the prints or adjust settings to fit your needs. Any slicer tips given below are for PrusaSlicer, though you may have to be in advanced or expert mode to access some settings.
Filament
- PETG is recommended (I used Overture translucent red for print in the images). PLA works as well but will be less durable.
Nozzle diameter
- 0.4 mm
Layer height
- Not important as long as you follow the instructions in the “Print Orientation” section. The models in the images above were printed at 0.25 mm.
- If starting from PrusaSlicer presets, use one of the “STRUCTURAL” options. Some of the features around the holes have thin walls that may cause issues if a “SPEED” option is used.
Supports
Supports are needed for the flipper. Here are some recommended support settings for the MK4S (feel free to adjust or dial these in based on your printers capabilities):
- Flipper:
- Overhang threshold: 40 degrees
- Style: Organic or Snug
- Top contact Z distance: 0.1 mm
- Bottom contact Z distance: same as top
- Tip diameter (if using organic): 0.4 mm
- IMPORTANT: make sure “Support on build plate only” is NOT CHECKED. You will likely need some very fine-point pliers, dentistry tools, mini-pick set, etc. to get the supports out of some holes.
- Case:
- You can probably get away without using supports. If your printer doesn't handle overhangs well, you can add the same support settings shown above to ensure the hole features turn out functional.
Skirt and Brim
A brim is recommended on all pieces except for “Small_Arm”. This helps bed adhesion and mitigates shrinking in the corners.
- Brim type: Outer brim only
- Brim Width: 7 mm
- Brim separation: 0.1 mm
Infill
- I used a 20% “Honeycomb” infill for the Case_Body, Case_Lid, Card_Frame and Flipper_Base pieces. This was largely an aesthetic choice to compliment the translucent filament. Feel free to experiment and change these to suite your filament type and durability needs. The Lever_Arm, and Small_Arm should be printed with a higher infill (>75%) to ensure longevity (I believe I printed these pieces with 100% infill, but that is probably overkill.)
PRINT ORIENTATION
The parts are designed to be printed in the orientation in which they appear below. These orientations help ensure the fidelity of the hole features and place the strength of the parts. You can print them in different orientations if you wish to save time, but you may need to adjust your layer height and support settings (or drill out some of the holes post-print) to ensure functional parts.
Important: If you are using a bed-slinger (like the MK4s), ensure you have the longer dimension of the pieces aligned with the axis in which the bed moves (see images below).
Flipper
Case
POST PROCESSING & ASSEMBLY
- Remove all brims and remove sharp edges with a hobby knife or deburring tool.
- Clean up the hole features on ONLY the Lever_Arm and Small_Arm pieces using a hobby knife or deburring tool (see image below). (IMPORTANT: Do not widen or alter the holes in the other pieces. The holes in the other pieces are meant to be tight in order to “catch” and secure the screws.) The hole features in ONLY the Lever_Arm and Small_Arm pieces should allow an M3 screw to rotate freely inside without resistance.
- Assemble the flipper and case according to the images below. Do not overtighten screws. Lever_Arm and Small_Arm should rotate freely and the mechanism should operate smoothly without much friction.




