Shelly box inline and wago 221 connectors (1Plus, 1L, 2PM, 2.5, Dimmer2)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
3,55 € – 4,34 € netto (bez VAT)
Dla pliku: shelly_enc_inline_box_v2_0.4n_0.2mm_PETG_MK4IS_3h35m.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 3,95 € netto (środek widełek).
- Masa podana przez autora
- 61 g
- Czas druku podany przez autora
- 3,59 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Enclosure designed to hold a Shelly with flex wires in line and wago 221 connectors.
- Ocena
- 5 / 5
- Polubienia
- 215
- Pobrania
- 1531
- Wydruki
- 11
- Wyświetlenia
- 10 836
- Oceny
- 9
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution
Part of my series of enclosures designed for Shelly smart devices and Wago 221 connectors.
- Shelly box for T&E 3x slots and wago 221 connectors
- Shelly box for inline flex wire and Wago 221 connectors (this one)
- Shelly box for 2x flex wires and wago 221 connectors
- Shelly box for 3x flex wires and wago 221 connectors
- Shelly quad box for 2x devices/5x relays/5x flex wires and wago 221 connectors
Shelly box for inline flex wire and Wago 221 connectors
This is an enclosure that I designed to hold a Shelly device associated wiring in a closed, electrically safe box. Wiring layout was planned so that the box sat inline between socket and appliance being controlled.
Electrical safety
- Mains electricity carries danger of death. Please don't attempt to use one of these with real circuits unless you are competent and aware of health and safety procedures.
- Use PETG or other fire resistant materials other than PLA.
Purpose and features
The box was designed to hold a Shelly Plus1 to control an appliance. It was fitted in line with a flex wire with a socket plug at one end and an IEC female plug at the other.
Shelly device support: Shelly Plus1, Shelly 1L, Shelly 2.5, Shelly 2PM, Shelly Dimmer2
Wire strain relief: Each twin&earth entry port has slots for fitting a cable tie as strain relief for the wires.
Attachment holes: The box has counter-sunk holes to attach it to a surface.
Cooling slots: There are cooling slots all around and above/below the shelly device.
Lid fitting: The lid attaches to the box using 4x M3 screws (5-10mm max) which thread into M3 heat inserts to be installed on the box.
Printing notes
- The lid requires supports on the bolt hole counter-bores, otherwise it will not print cleanly (in my case it didn't)
Version control
Version 2.1 - 11/03/2024
- Updated (reduced) cable tie shelf width, validated lid locator and wago pad locations
Version 2.0 was a significant redesign to include the following features:
- M3 heat thread inserts instead of square nut slots or holes for tapping
- Attachment bolt holes on the inside of the box rather than outside brackets
- Cable tie pads inside the box as opposed to accessible from the outside (enables refitting ties without dismounting the box)
- Shelly slot adjusted for compatibility with multiple models